Dislikes: 0
-
Regular Member
6in Orbital to 15mm
Hey everyone (I'm just full of questions today), I'm kicking the idea of upgrading the 6in DA to the BOSS 15mm throw orbital.
How does the 15mm throw handle curves compared to the 8mm throw? Do you notice a real difference in the amount of time you spend working on compounding and polishing? Does the added power make a difference during your process? Are these differences worth the added cost?
Thanks for you input!
Sent from my SM-G950U using Autogeekonline mobile app
-
Super Member
Re: 6in Orbital to 15mm
the larger the stroke, the more prone to stalling (you'll have to adjust to the panel/contour) and that's with any/all long throw polishers. the advantage is it will cover more ground, be smoother, and more comfortable to use. that's why it's ideal to have a few different polishers. keep your current polisher and equip it with a smaller pad set-up..
-
Post Thanks / Like - 0 Thanks, 2 Likes, 0 Dislikes
-
Regular Member
Re: 6in Orbital to 15mm
Originally Posted by VISITOR
the larger the stroke, the more prone to stalling (you'll have to adjust to the panel/contour) and that's with any/all long throw polishers. the advantage is it will cover more ground, be smoother, and more comfortable to use. that's why it's ideal to have a few different polishers. keep your current polisher and equip it with a smaller pad set-up..
I'm running a 5in pad on it. I use the Lake Country flat pads right now. I'm considering switching to the thin pads though.
Sent from my SM-G950U using Autogeekonline mobile app
-
Super Member
Re: 6in Orbital to 15mm
I went from a Porter Cable 7424 to a Boss 21, no issues or stalling. Made work on my Dodge Charger, buddys Challenger and Titan truck go so much faster.
I'm not a pro, but with a kid, work and other life, I dont have as much time to detail. The Griots 21 was a dream! I also have the 5inch backing plate for the G21. My PC now has a 3inch BP for smaller areas.
-
Post Thanks / Like - 0 Thanks, 3 Likes, 0 Dislikes
-
Super Member
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
-
Super Member
Re: 6in Orbital to 15mm
Originally Posted by AaronE
I'm running a 5in pad on it. I use the Lake Country flat pads right now. I'm considering switching to the thin pads though.
Sent from my SM-G950U using Autogeekonline mobile app
I found that the thin pads were better on my PC. But Dan (dlc95) turned me on to the "light touch method". I swear it works. Just keep enough pressure on the surface to keep it spinning max RPM's while using a great abrasive, and you can get great results using even thicker (7/8") pads.
FWIW, I am a big Lake Country flat pad fan.
It is no coincidence that man's best friend cannot talk.
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
-
Regular Member
Re: 6in Orbital to 15mm
Originally Posted by 392hemi
I went from a Porter Cable 7424 to a Boss 21, no issues or stalling. Made work on my Dodge Charger, buddys Challenger and Titan truck go so much faster.
I'm not a pro, but with a kid, work and other life, I dont have as much time to detail. The Griots 21 was a dream! I also have the 5inch backing plate for the G21. My PC now has a 3inch BP for smaller areas.
I'm in the same boat with my time being limited due to family, work, military, school, life, and probably two other things I cannot even think of right now. How much time would you say you saved? I.e. 25% 50%, etc. Just a ballpark guess.
-
Regular Member
Re: 6in Orbital to 15mm
Originally Posted by PaulMys
I found that the thin pads were better on my PC. But Dan (dlc95) turned me on to the "light touch method". I swear it works. Just keep enough pressure on the surface to keep it spinning max RPM's while using a great abrasive, and you can get great results using even thicker (7/8") pads.
FWIW, I am a big Lake Country flat pad fan.
I do try to keep a light had on my GG6in (~ 5lbs of pressure is my goal) and run Megs Mirror Glaze polishing products (M105/205 combo usually). I don't notice too much bogging down with the flat pads myself honestly. I just figured if they weren't helping my work time then I'd consider a switch. I'm namely trying to save some time without sacrificing the ability to have a machine to tackle whatever project body shape I take on.
-
Super Member
Re: 6in Orbital to 15mm
Originally Posted by AaronE
I'm in the same boat with my time being limited due to family, work, military, school, life, and probably two other things I cannot even think of right now. How much time would you say you saved? I.e. 25% 50%, etc. Just a ballpark guess.
I was dealing with an auto body shop and "detailer" that destroyed my immaculate finish. The PC was just taking too long to work and could not get to 100 percent.
See here
Help detailer trashed my paint!
Being OCD and annoyed at stalling of the PC on my hood, I bought the Boss G21. A couple of things, it is a lot smoother and less taxing on my body than the PC, I would say it cut my time in half.
You can't go wrong with any of the upgrades in machines, be it 15, 21. Rupes, Flex or Griots.
I got my car back to 99.99 percent and the G21 did not stall. I've done other larger cars, it just is so much faster due to the longer stroke and power. Takes way less passes.
-
Regular Member
Re: 6in Orbital to 15mm
Originally Posted by 392hemi
I was dealing with an auto body shop and "detailer" that destroyed my immaculate finish. The PC was just taking too long to work and could not get to 100 percent.
See here
Help detailer trashed my paint!
Being OCD and annoyed at stalling of the PC on my hood, I bought the Boss G21. A couple of things, it is a lot smoother and less taxing on my body than the PC, I would say it cut my time in half.
You can't go wrong with any of the upgrades in machines, be it 15, 21. Rupes, Flex or Griots.
I got my car back to 99.99 percent and the G21 did not stall. I've done other larger cars, it just is so much faster due to the longer stroke and power. Takes way less passes.
You're definitely talking me into going for the G21 instead now. With a smaller pad (5in plate and 5.5in diameter, 1/2in thick LC flat pad) I shouldn't bog down on the curves of the cars or the airplanes (the REALLY time draining/life sucking polishing projects I do) I would imagine.
Similar Threads
-
By Mike Phillips in forum PICTURES: 3-Day CAR Detailing Bootcamp Classes
Replies: 2
Last Post: 04-06-2018, 02:40 PM
-
By Mike Phillips in forum Ask your detailing questions!
Replies: 5
Last Post: 11-17-2016, 08:46 AM
-
By Mike Phillips in forum Product Reviews by Mike Phillips
Replies: 15
Last Post: 04-24-2016, 02:15 AM
-
By Mike Phillips in forum Product Reviews by Mike Phillips
Replies: 89
Last Post: 03-15-2016, 12:26 PM
-
By Mike Phillips in forum Ask your detailing questions!
Replies: 25
Last Post: 02-18-2016, 09:29 PM
Members who have read this thread: 0
There are no members to list at the moment.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
S |
M |
T |
W |
T |
F |
S |
28 | 29 | 30 |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
31
| 1 |
|
Bookmarks