Dislikes: 0
-
04-23-2024, 10:31 PM
#1411
Super Member
Re: DFB's Garage
Have a look at bojo trim tools from Ultracut Australia.
-
04-24-2024, 02:30 AM
#1412
Super Member
Re: DFB's Garage
Originally Posted by DFB
Wildtrak Seat Trim Replacement
Some time ago, the drivers side seat base trim valance on the Wildtrak broke. From memory, the XLT that this car replaced also did the same, so I’m pretty sure this is a common failure part.
From what I can tell, the way the trim is shaped and attached to the seat has it subjected to substantial pressure as the driver enters and exits the vehicle. Repeated cycles of compression and release sees the plastic fatiguing over time, which then leads to it cracking.
Could I have made a warranty claim on this failure? Perhaps, but unlikely. Apart from the fact that its just outside of warranty now, Ford would likely claim it as wear and tear, which is fair enough. As such, I decided to order the part from Bayford and do the job myself.
There are a few different versions of this part, all dependent on trim and model spec, and of course driver or passenger orientation. For example, the same part in my Ranger would not have cut-outs for power seat adjustment but would have a mechanical backrest lever. There are also two versions for the 8-way powered Wildtrak, with or without seat heating. This particular Wildtrak is not equipped with seat heaters. At this point, I would list the part number and provide the link, but more on that in later.
First, I removed the two electric seat adjustment levers with my fancy skin wedge tool. There is also a singular Phillips head screw on the rear of the seat. The trim is then "massaged" from the locator tabs.
Next, remove the two screws holding the switch module to the trim, you then need to release it from the tabs.
For the new trim, refit the switch module, then wrangle the trim into place to align and then snap into the three locator tabs, replace the rear screw. The adjuster levers then snap back into place. But........................
Despite being a professional online shopper, for some reason I bought the wrong part. I think the new one is for an XLT and not the Wildtrak with its black rather than grey plastics. I've tried searching the part number for the old piece, but I can only find the grey version.
Does it matter? To me it does, to my father, not at all. I might try and track down the correct part, but I guess its not critical concern. I'm just chuffed I managed to do this myself.
Well, it got the better of me!
I had the local Ford dealer find the correct part, which was ordered late yesterday and was at the parts department by 9am this morning. Can't beat that for turnaround, not to mention not paying for shipping.
-
Post Thanks / Like - 0 Thanks, 2 Likes, 0 Dislikes
-
04-24-2024, 05:27 AM
#1413
Super Member
Re: DFB's Garage
Originally Posted by Tasmania
Have a look at bojo trim tools from Ultracut Australia.
Those look very enticing, almost too many to chose from so I'm not sure where to start.
I have my eye on the new Detail Factory Pick Set, they haven't arrived in Australia yet though.
-
Post Thanks / Like - 0 Thanks, 2 Likes, 0 Dislikes
-
04-25-2024, 12:43 AM
#1414
Super Member
Re: DFB's Garage
I feel so much better now.....................
Black -
River Rock Silver, not the contrast to the black switch levers -
And what I would have preferred to include in the original post, the part number. If you have a PX MK III Ranger Wildtrak WITH 8-way powered seat but WITHOUT seat heating, you want the following part in black and NOT River Rock silver -
EB3Z 17A861 FH
You would think that having done this before, removing the wrong part and putting the correct one on would have been easy. NO!
The incorrect part put up a fight and I broke one of the rear locator tabs, which is no matter because I have no use for it anyway. The new part went on pretty good but.....................then I realized I forgot to reattach the two screws that secure the adjustment module to the trim. Rookie!!
So, off the trim comes, screws reattached and then the fight started. I got the thing on again, but something didn't look right, and I somehow unhooked the front of base cushion from the seat frame. It was then I realized I hadn't slotted the front of the trim to the frame properly, so off it came again. I got everything lined up and clicked into place, I then had to fight that final screw to get it properly aligned.
What was going to be a 10-minute job turned into 45 minutes. A lot of that was moving the seat base and backrest up/down/backwards/forwards. It's at this point I have to wonder why powered seat bases are seen as a luxury, every movement takes far longer than a manual adjustment lever.
In any case, I don't mind, I think this is what they call a "learning experience".
-
Post Thanks / Like - 1 Thanks, 1 Likes, 0 Dislikes
Similar Threads
-
By Matador in forum Auto Detailing 101
Replies: 7
Last Post: 08-11-2021, 06:22 PM
-
By Nick McKees37 in forum How to Articles
Replies: 3
Last Post: 02-17-2015, 11:14 AM
-
By Mike Phillips in forum Off-Topic
Replies: 5
Last Post: 09-17-2010, 09:47 PM
-
By Mike Phillips in forum PICTURES: 3-Day CAR Detailing Bootcamp Classes
Replies: 20
Last Post: 06-28-2010, 03:05 PM
-
By Mike Phillips in forum How to articles
Replies: 3
Last Post: 06-23-2010, 01:00 PM
Members who have read this thread: 84
- rmtaylor51,
- RPPM,
- KirkH,
- cb804,
- ev780,
- Dyerlog,
- mikeinauburn,
- GrnEyeDog,
- AMarkham40,
- BTW574,
- FocusSTguy,
- melF1fan,
- jstollar,
- PaulMys,
- Gridlink,
- barryscott,
- Dynoguy,
- The Guz,
- Jplouch,
- ellens2,
- no cigar,
- Bosko,
- D.BRITT,
- cyclops,
- delt1964,
- tradecraft1,
- chris87,
- vaced,
- John U,
- jrose0070,
- Danube,
- aannatshlzea6696,
- ollever,
- 02whitetundra,
- VISITOR,
- Rsurfer,
- 11Silverado,
- Desertnate,
- Ace22,
- damonb10,
- JSkibisky,
- georgia boy,
- gregory1420,
- chris12,
- larr12,
- gibby68,
- filhotran,
- TroyScherer,
- Awickedtruth,
- Alansr,
- DG3.7,
- eveausasdy529,
- Wknd Dtlr,
- pdl2mtl90,
- Mklauss,
- T-STeve,
- msharpe785,
- Setec Astronomy,
- chilly,
- ajdavies91,
- Silly Rabbit,
- Thunderchicken,
- 2FORDS,
- oneheadlite,
- DanaDetailingPros,
- SNP209,
- Dirty Harry,
- Vegas1,
- bapatickmjnra7168,
- bill walsh,
- Tasmania,
- DFB,
- dbeng,
- Prange,
- brianshaeffer,
- Azure,
- hansen97,
- Karl_in_Chicago,
- Odrapnew,
- kappy,
- WillSin865,
- wierdkid,
- Texchappy,
- chefwong
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
S |
M |
T |
W |
T |
F |
S |
31 |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
| 1 | 2 | 3 | 4 |
|
Bookmarks