Chrome has much better security than either FF or IE. Chrome runs each tab you open in its own process and sandboxes them from each other and your computer. As far as I know Chrome has never been...
Executive Orders directly from the President as well as regulations from Regulatory Agencies such as OSHA, EPA, BATF, and TSA under DHS make sweeping decisions with no Congressional input all the...
Nope! AFLCIO and SEIU Unions wouldn't allow it. He has labor camps full of "free" labor building his toys. Bloomberg and the anti-salt crowd would come down on him for his over-eating habits. PETA...
On a side note, the left has their own beloved red-headed stepchild to deal with as it appears Nader is talking about making another primary challenge against Obama. 2012 will definitely be...
I should also say that I will not be voting for Trump in any primaries. However, if it does come down to Trump vs Obama I will do what I did with McCain and vote for the lesser of two evils. I'm just...
If you honestly think that Hillary Clinton would have been treated differently by the conservative movement if she was in office doing the same thing as Obama, you really have no clue what the...
Yeah, I had mixed results with it. I didn't have to wait at all with OPC, just sprayed it carefully onto the trim, carefully avoiding overspray onto the paint as I didn't want to remove LSP and went...
Over the last 9 months I had tried DG #481, IPA, clay, vinyl erasers, etc. all recommended on these forums on my GF's gray textured hard plastic on her 2010 mustang. It had been stained by WGDGPS 3.0...
I saw in another thread that the OP used foaming glass cleaner to remove polish oils as it clings and stays on the panels especially vertical panels to better break down the oils than a liquid glass...
Which System 51 polish do you use/prefer...Perfect Cutting Polish or Pro Cut Polish? How do they compare to G|Techniq P1 and P2 (if you've ever used P2) in cut/finish?
Great video Garry. Also watched the one you had telling everyone to polish the trim...care to do a video on that process when you get a chance? Is it much different than paint polishing?...
Why "Gtechniq P2 via PCXP with Cyan LC pads"? Isn't P2 a finishing polish and LC Cyan a cutting pad? Can you elaborate on your results with this combo? I've seen you mention it before in...
Well I still have a little bit of Opti-Clean here at the house...my lady has the rest of the gallon at her house. I have a ton of UWWP. I, unfortunately, do not have any of the DP Concentrate. I...
Good idea and that will definitely be more controlled. Although it will have to wait like I said above. Fortunately, for this test at least, the real pollen hasn't started yet....a few more weeks...
My car is garaged when I get to the house as well...but the Air Force Base I work on has a ton of Bradford Pear Trees. I understand that there was already a very small layer of pollen/dust on the...
For all the avid Ultima Waterless Wash Plush users out there (CEEDOG and OldTiger especially) do you notice any significant attraction of pollen or dust to areas wiped with UWWP? I started using...
20%!?!? :wow: I almost never rely on factory calibration as the environment of mass production and environmental conditions play a large part in the reading. Personally, I think that the device...
Thanks for posting the pic mxfly! Yep I do not have the shims nor the paper possessing the table that describes them in you pic. I called Brad at Highline yesterday. He said that it was the very...
Well after conversing with Chad (Rasky) via PM on this it appears that I am missing the plastic shims entirely out of my shipment. He said there were 5 in the one he has. Mine had zero! No wonder I...
Hmm....might have to see if I can get some additional shims that go below the 0.001 thickness. If all this meter can do with calibration is two points though, I wonder if it would be more...