Thanks: 0
Likes: 0
Dislikes: 0
-
Question on selecting pads to work in tight areas
I have a few questions regarding my 7424 and polshing pads. I am getting ready to purchase a few things and I need to get some pads to corrct the top part of my rear bumpr. It has never been machine polished before due to the fact that there it not too much of a overgang lip to really fit a pad to do so. If I used a 5.5" pads, there'd be some overhang off the edge while polishing. I don't know if this is a good idea or not, or if this could cause the pad to flex around when it's not making contact and cause more of a problem. Or I could use a 4" pad, but from what I have read these are intended to be used to correct a small defect or a small section. Are these safe enough and will hold up long enough to do something such as to top part of my rear?
If a 4" pad is the way to go, is there a different counterweight that must be used for much smaller pads? I noticed on the original weight on my 7424 it says to use 5" pads
-
Super Member
Re: Question on selecting pads to work in tight areas
I bought a Griot's Garage 3" RO polisher from Autogeek for just that reason. It's also great for doing the A/B/C pillars, painted mirrors, etc. I've even used it to polish glass, headlamps and tail lights.
2007 Ford Edge SEL AWD 2006 Ford Mustang GT 2009 Ford F-150 XLT Supercab 4x4
-
Re: Question on selecting pads to work in tight areas
Originally Posted by 05RLS2
I have a few questions regarding my 7424 and polshing pads. I am getting ready to purchase a few things and I need to get some pads to corrct the top part of my rear bumpr. It has never been machine polished before due to the fact that there it not too much of a overgang lip to really fit a pad to do so. If I used a 5.5" pads, there'd be some overhang off the edge while polishing. I don't know if this is a good idea or not, or if this could cause the pad to flex around when it's not making contact and cause more of a problem. Or I could use a 4" pad, but from what I have read these are intended to be used to correct a small defect or a small section. Are these safe enough and will hold up long enough to do something such as to top part of my rear?
If a 4" pad is the way to go, is there a different counterweight that must be used for much smaller pads? I noticed on the original weight on my 7424 it says to use 5" pads
I have the same issue with my wife's Lexus. The LC 4" HT or CCS pads will work for this area. Just be aware that apparently because of the 1.25" thickness, the 4" pads don't correct as quickly as the thin 5.5 pads. I had to really back off on the pressure as the pads will squash and stop spinning quite easily and I had go to a longer polish time and multiple passes with the same compound to get the correction and gloss I wanted.
-
Super Member
Re: Question on selecting pads to work in tight areas
I'm not sure for your PC specifically but I can tell you 4" pads will hold up fine. I was using the FLex Edge adapter with 4" pads (a story unto itslef) but my buddy had a custom Flex BP made for me that is just less than 4" in dia. With this I purchased a pile of 4" HT pads and so far I love them as much as my 6 1/2" pads.
:dancebanana:
Sky's the Limit Car Care
-
Re: Question on selecting pads to work in tight areas
I really like the Buff & Shine 4 in pads. The center is recessed for you BP and the shape of the foam in perfect for tight areas.
-
Super Member
Re: Question on selecting pads to work in tight areas
Originally Posted by Troy Fuller
I really like the Buff & Shine 4 in pads. The center is recessed for you BP and the shape of the foam in perfect for tight areas.
That'll be my next purchase. The 5.5" pads are amazing.
-
Re: Question on selecting pads to work in tight areas
Originally Posted by HeavyMetal
I have the same issue with my wife's Lexus. The LC 4" HT or CCS pads will work for this area. Just be aware that apparently because of the 1.25" thickness, the 4" pads don't correct as quickly as the thin 5.5 pads. I had to really back off on the pressure as the pads will squash and stop spinning quite easily and I had go to a longer polish time and multiple passes with the same compound to get the correction and gloss I wanted.
That makes sense due to the thickness. With the 5.5" pads do you not get vibrations from the pad when it it not making contact to the surface? I always though that this could always cause more marring due to the fact that the pad might be off balanced
Similar Threads
-
By DKenn08 in forum Auto Detailing 101
Replies: 15
Last Post: 05-24-2015, 07:39 PM
-
By frankprozzoly in forum Auto Detailing 101
Replies: 6
Last Post: 05-27-2014, 10:06 AM
-
By sushi in forum Auto Detailing 101
Replies: 10
Last Post: 04-06-2012, 11:20 AM
-
By Mark Preus in forum Ask your detailing questions!
Replies: 6
Last Post: 02-17-2010, 07:56 PM
-
By RaskyR1 in forum Wet-Sanding, Cutting & Buffing
Replies: 6
Last Post: 01-28-2010, 06:33 PM
Members who have read this thread: 0
There are no members to list at the moment.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
S |
M |
T |
W |
T |
F |
S |
28 | 29 | 30 |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
31
| 1 |
|
Bookmarks