Thanks: 0
Likes: 0
Dislikes: 0
-
Re: Backing plate stud height and diameter for 5/16" thread.
Originally Posted by mengelhardt
Mike, I'm thinking it is a coarse thread too, but I was just looking at the buffdaddy site, and according to his site, it's a 5/16-24 thread......
If his site is correct, that would be a fine thread, and we'd be wrong...
I'm not with my detailing supplies, so I can't check for sure.
That's probably correct, Kevin is always very accurate I his writing. Not that I'm not but sometimes I simply type faster than I think.
Just walked out to the garage and looked at the stud on an LC DA Backing Plate and it is in fact fine thread.
-
Re: Backing plate stud height and diameter for 5/16" thread.
Originally Posted by Buracho
I hope to share it here if it ia a success.
Can you help me out?
Not sure what you're working on but if it's going to be a retail product the correct procedure to market it on this forum would be to first get it into the AG store and that process is to send your info to
info@autogeek.net
The information is then routed to the appropriate department and if there is any interest that department will contact you.
-
Junior Member
Re: Backing plate stud height and diameter for 5/16" thread.
Originally Posted by FUNX650
Thanks Bob.I think that settels it.
-
Junior Member
Re: Backing plate stud height and diameter for 5/16" thread.
Originally Posted by Mike Phillips
Not sure what you're working on but if it's going to be a retail product the correct procedure to market it on this forum would be to first get it into the AG store and that process is to send your info to
info@autogeek.net
The information is then routed to the appropriate department and if there is any interest that department will contact you.
Thanks for your help Mike.
It is nothing major just a home experiment hopefully to make buffing easier, hopefully
Non the less i will make sure to follow your advice. I appreciate it.
-
Junior Member
Re: Backing plate stud height and diameter for 5/16" thread.
My work will be complete with additional measurements from you guys,
Height and Thickness/diameter.
that would be awesome
-
Re: Backing plate stud height and diameter for 5/16" thread.
5/16 - 24 I know because I made a backing plate extension 2 weeks ago
-
Junior Member
Re: Backing plate stud height and diameter for 5/16" thread.
Originally Posted by thesilverone
5/16 - 24 I know because I made a backing plate extension 2 weeks ago
Thanks thesilverone, Any idea of the height? Without yor mod i mean.
-
Re: Backing plate stud height and diameter for 5/16" thread.
It's 5/16-24 Thread and about 7/16" long.
That's measured without the compression washer in place.
I measured both a meguiars and a Lake Country backer, both were the same length.
-
Junior Member
Re: Backing plate stud height and diameter for 5/16" thread.
Originally Posted by mengelhardt
It's 5/16-24 Thread and about 7/16" long.
That's measured without the compression washer in place.
I measured both a meguiars and a Lake Country backer, both were the same length.
Awesome! Thanks very much bro.
Similar Threads
-
By MartyK in forum Ask your detailing questions!
Replies: 19
Last Post: 05-31-2020, 02:42 AM
-
By willowcat11 in forum Auto Detailing 101
Replies: 9
Last Post: 03-03-2016, 11:43 AM
-
By dennis hiip in forum Auto Detailing 101
Replies: 17
Last Post: 09-16-2014, 05:01 PM
-
By ryanmcg1 in forum Product Reviews
Replies: 8
Last Post: 09-29-2011, 11:29 PM
-
By Mindflux in forum Wet-Sanding, Cutting & Buffing
Replies: 4
Last Post: 06-09-2010, 11:48 AM
Members who have read this thread: 0
There are no members to list at the moment.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
S |
M |
T |
W |
T |
F |
S |
31 |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
| 1 | 2 | 3 | 4 |
|
Bookmarks