Please give your best coating application tips…

[Eric7810]

Guys, I’ve been doing coatings for a few years now. I’ve got two or three happening each week now and am curious your best tips for applying and leveling.

I run a dehumidifier. Seems to help.

What is your favorite towel?

I still struggle with ‘streaky-ness’ on certain jobs. I look at it with a scan grip headlamp on warm white to find streaks. Honestly I think the streaks happen because I haven’t panel wiped well enough.

I use new towels on every job. Sometimes grab new ones halfway through.

On sunny days I’ll bounce light from outside onto the paint with a poster board to find highs but if it’s cloudy I’ll back the vehicle outside and find them.


Sent from my iPhone using Tapatalk

[TTQ B4U]

Switch to GYEON's new EVO Products. It doesn't get any easier to apply. You won't get streaks unless you drip grease from your lunch on the surface.

[DFB]

Guys, I’ve been doing coatings for a few years now. I’ve got two or three happening each week now and am curious your best tips for applying and leveling.

I run a dehumidifier. Seems to help.

What is your favorite towel?

I still struggle with ‘streaky-ness’ on certain jobs. I look at it with a scan grip headlamp on warm white to find streaks. Honestly I think the streaks happen because I haven’t panel wiped well enough.

I use new towels on every job. Sometimes grab new ones halfway through.

On sunny days I’ll bounce light from outside onto the paint with a poster board to find highs but if it’s cloudy I’ll back the vehicle outside and find them.


Sent from my iPhone using Tapatalk

What coatings are you using?

[Desertnate]

I run a dehumidifier. Seems to help.

I've found temperature seems to have a bigger effect than humidity. The warmer it gets the faster the coating flashes with thee sweet spots around 70F.

I still struggle with ‘streaky-ness’ on certain jobs. I look at it with a scan grip headlamp on warm white to find streaks. Honestly I think the streaks happen because I haven’t panel wiped well enough.

I'm not sure what your streaks look like, but when encountering a similar issue I found it was due to a couple things: buffing the coating too early and not swapping out my low nap towel often enough.[/QUOTE]

Switch to GYEON's new EVO Products. It doesn't get any easier to apply. You won't get streaks unless you drip grease from your lunch on the surface

Yes, very easy to apply flawlessly, especially with Mohs EVO. It's almost as easy as a sealant.

I'm sure you'll get lots of good tips, but the game changer for me was how I approached my lighting. When I started using diffused, reflected lighting that simulated a cloudy day, it really changed the quality of my applications. I turn off all overhead lighting and then rotate the lights on my stand to reflect light off a wall or ceiling depending on where I'm at on the car. For horizontal surfaces I'll aim them at the ceiling and on vertical surfaces I'll usually aim them at the top of the wall behind me where I'm working. By doing this I found I'm seeing the actual surface conditions rather than seeing the paint below the clear or getting dazzled by the metallic flake in the paint.

[Eric7810]

Thanks already guys…

I am using Cquartz UK 3.0


Sent from my iPhone using Tapatalk

[Optimus Grime]

I'm in the Gyeon camp. It can't get any easier and the results are top notch. Give Mohs a try on a vehicle and see how you like it.

[DFB]

Thanks already guys…

I am using Cquartz UK 3.0


Sent from my iPhone using Tapatalk

Not that I have used the product, but I have heard of people having similar issues with Cquartz UK 3.0, on the flipside others say its easy to use. Go figure.

I would consider trying something new, if the UK 3.0 is giving you grief, then it's time to move on. As other have mentioned, Gyeon Pure EVO and Mohs EVO were designed with user friendliness in mind. Pure EVO is a wipe on, wipe off application but can be left on the panel for 10 minutes before leveling. Mohs has a more traditional application but offers superior slickness.

[Desertnate]

Not that I have used the product, but I have heard of people having similar issues with Cquartz UK 3.0, on the flipside others say its easy to use. Go figure.

I think people praising it's ease of use like the long flash times it offers. It allows you to apply to the entire side of a mid-sized vehicle (if the temps are cool enough) before buffing off and it also gives you a pretty large window of time to fix any errors. The down side to this long flash time, from my use of CQUK 3.0, is if you get a little impatient and try to buff it out too early, you'll get streaks and smears. I found the getting the removal timing right on 3.0 much harder than with 2.0 which had a much shorter flash time.

ure EVO is a wipe on, wipe off application but can be left on the panel for 10 minutes before leveling. Mohs has a more traditional application but offers superior slickness.

I think you might have that backwards. Mohs you apply and it beads up/sweats (rather than flashing) almost instantly and can be wiped off. Pure will flash over a couple minutes like other coatings.

I'd also caveat the 10 minutes of dwell time with being cautious about ambient temperatures. I appled Pure to my car last weekend. When I started the work in the morning when my garage was pretty cool. Flash times were generous and you could let it sit for a few minutes. By the end of the job the things had warmed up and I found I only had a couple minutes to do any removal. It flashed much quicker and the removal window was only a couple minutes before it became difficult.

[Eric7810]

I’ll be honest this is not the advice I wanted to hear LOL..

I’ve got lots of UK 3.0 backstock, but I’ll give Mohs a try for sure and see how I feel.

The thing with UK is I can have jobs that go silky smooth, and others where I have a sore arm and wrist afterwards because I spent so much time fighting and wiping smear marks. Especially on glass.


Sent from my iPhone using Tapatalk

[Desertnate]

I did OK with CQUK. It was my go-to for a long time. The trick to eliminate smearing for me was catching the flashing at the right moment and having the lighting set to improve visibility of the flash. It's a good coating and I'd use it again. I just like Mohs EVO better now that I've tried it.

Just another thought. Could you be applying it a bit too heavy which slows the flashing and causes it to smear when you buff it off? My smearing issues with any coating has come down to buffing off the coating a little too early. I actually encountered it with Pure EVO last weekend when I applied it too thick in a couple places.