Griots ceramic all in one

[Odrapnew]

I got some 3-1 AIO today

I’m surprised how thin and watery it is

Super separated as well

Is this ok?

Wondering if I need to return it


Sent from my iPhone using Tapatalk

The bottle I picked up was separated as well. I shook it up and looked fine.
I don't think it was any more runny than the Megs UP that I have.

My 3-in-1 spray has some settling as well and needs a shake before use.

My thought is that it's normal.

[MisterSnoop]

I didn't check if mine was separated but it did seem very thin.

[chilly]

Well I just shook the crap out of mine and it’s not so thin now

I don’t want to break the inner seal and check in it because it’s going back to Hawaii in my luggage along with the Speed Shine

In double freezer bags of course




Sent from my iPhone using Tapatalk

[Bosko]

I breezed through posts and all I got out of it was...."mine is thin even after I shook it".....sounds like bad genetics.....

[chilly]

I am hoping someone here does a full on review of this product before I try it out

The lack of info on the Griot's site is maddening

I know they pulled it for whatever reason but it's quite obviously out there to be purchased so WTH

I only found one vid on YouTube and after the guy clayed his car without using any lube I shut it off before he even got to the AIO part

What Sam said about wipeoff in the video linked earlier confused me

Wipe it off immediately after finishing a section?

Wait until you are through with half the car?

What he said about the AIO and other ceramic products didn't make sense to me

[MisterSnoop]

I am hoping someone here does a full on review of this product before I try it out

The lack of info on the Griot's site is maddening

I know they pulled it for whatever reason but it's quite obviously out there to be purchased so WTH

I only found one vid on YouTube and after the guy clayed his car without using any lube I shut it off before he even got to the AIO part

What Sam said about wipeoff in the video linked earlier confused me

Wipe it off immediately after finishing a section?

Wait until you are through with half the car?

What he said about the AIO and other ceramic products didn't make sense to me

yeah, it's frustrating that it's been radio silence on it since it became available. they have a live stream next week. maybe they'll talk about it then.

here's an earlier video from SEMA which mentions doing it one panel at a time. apply to a panel, wipe off, then move to the next panel.
Log into Facebook

[chilly]

yeah, it's frustrating that it's been radio silence on it since it became available. they have a live stream next week. maybe they'll talk about it then.

here's an earlier video from SEMA which mentions doing it one panel at a time. apply to a panel, wipe off, then move to the next panel.
Log into Facebook

Thanks but I don't do Facebook

This forum is the limit of my social media

A panel at a time makes sense though

I am sure they realize people will be dying to layer 3 in 1 over it and eventually talk about the timing for that as well

[MisterSnoop]

this is what it says: "simply apply it, one panel at a time. wipe it off. and work your way around the car."

I asked them about timing on doing a layer of 3-in-1 after it and they said wait 12-24 hrs.

[chilly]

this is what it says: "simply apply it, one panel at a time. wipe it off. and work your way around the car."

I asked them about timing on doing a layer of 3-in-1 after it and they said wait 12-24 hrs.

Works for me

Fanks!

Now I gotta wait 7 weeks...

[Odrapnew]

I may have done it a little incorrectly when I tried it last weekend.
I did the usual section and wipe off like I've done with polish. Maybe I should have let it sit on there for longer?

Anyway, water beading on the hood is just as good as any other part of the car which has 3-in-1 spray.
I might give it a wash this weekend and provide some more input.