-
Super Member
Brand New Wheel Coating
I have a brand new set of wheels that I intend to Ceramic coat in the near future.
Would I need to clay and iron decon these or just skip to an IPA wipe down prior to coating?
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
-
Super Member
Re: Brand New Wheel Coating
An IPA wipedown would just fine but I can't wait to see them on the Stang Not only will is dramatically change the look of your car but it's one less set of gloss black wheels on the road
Sent from my SM-G950U using Tapatalk
2022 Elantra N Cyber Gray
Some say..."He likes Swedish fish because they're made with caranuba wax"
-
Post Thanks / Like - 0 Thanks, 2 Likes, 0 Dislikes
-
Super Member
Re: Brand New Wheel Coating
I wouldn't clay unless you were going to polish them. Clay should not be needed on new wheels.
Iron decon shouldn't be needed either but it's easy enough to do to find out.
Then wipe them down.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
DFB thanked for this post
-
Super Member
Re: Brand New Wheel Coating
When I coated a new set of wheels, I hit them with an APC and a soft cloth to clean off any grime from shipping. I followed that up Eraser and then applied the coating. Like others have said, no polishing, claying, etc needed.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
DFB thanked for this post
-
Super Member
Re: Brand New Wheel Coating
THOSE are a great looking set of wheels!
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
DFB liked this post
-
Super Member
Re: Brand New Wheel Coating
Panel wipe and coat. Coat them after the tires have been put on.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
DFB thanked for this post
-
Re: Brand New Wheel Coating
You shouldn't need to do either. If you want to, you can use an iron spray on your wheels as it really doesn't take much time, but when my Vorshalg wheels where brand new I did an iron spray and they did not need it. Panel wipe/eraser/ipa is all that should need to be done.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
DFB thanked for this post
-
Super Member
Re: Brand New Wheel Coating
Thanks for the input everyone, pretty much confirms what I was planning to do. I will give them a thorough wipe down with Eraser then straight to coating.
I have no issues doing an iron decon but, and I can't believe I'm saying this, I don't see the point in wasting chemical if it's not needed. Especially if it means avoiding the stench of IronX.
These wheels have a matte finish so polishing would not be desirable. I know the coating will add some gloss but I'm fine with that.
I also intend to coat the front Brembo calipers. I will perform the Iron decon for this job though.
I now wish I had red calipers to match the Race Red body though.
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
-
Super Member
Re: Brand New Wheel Coating
Does the Stang not have rear Brembos?
Sent from my SM-G950U using Tapatalk
2022 Elantra N Cyber Gray
Some say..."He likes Swedish fish because they're made with caranuba wax"
-
Super Member
Re: Brand New Wheel Coating
Originally Posted by
Klasse Act
Does the Stang not have rear Brembos?
Sent from my SM-G950U using Tapatalk
Only GT-350 / GT-500 got rear Brembo's.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
Bookmarks