Dislikes: 0
-
Regular Member
-
Super Member
Re: How restore deep satin black between cab windows ?
For something like that I’d first try Hyper Polish or McKee’s paint prep polish. Both work incredibly well on vinyl and smooth black trim. If either of those works, I’d top with PNS or BSD.
I was going to say if it was yours or a friends, just put some new vinyl on. I have a 2010 Tundra and when mine was getting too thin to be polished out, I just removed it and installed some 3M Dinoc carbon vinyl. Very subtle, yet noticeable.
-
Regular Member
Re: How restore deep satin black between cab windows ?
Originally Posted by fly07sti
For something like that I’d first try Hyper Polish or McKee’s paint prep polish. Both work incredibly well on vinyl and smooth black trim. If either of those works, I’d top with PNS or BSD.
I was going to say if it was yours or a friends, just put some new vinyl on. I have a 2010 Tundra and when mine was getting too thin to be polished out, I just removed it and installed some 3M Dinoc carbon vinyl. Very subtle, yet noticeable.
Thanks much for the suggestions. On mine, the black extends beneath the rubber trim adjacent to the panels so I think it would be difficult for me to do a clean edged job if I were to try rewrapping, but it might be the way to go.
As far as PNS goes, I just tried it a few days ago over the D166. I'm anxious to see how it holds up in the desert heat.
Rick......(Spelled with a "D" )
-
Re: How restore deep satin black between cab windows ?
Hard to tell from the images but based on the fading pattern and gloss levels, it looks like it is vinyl wrapped.
If you were to fix it, re-wrapping would be the way to go (even if it is painted). To get the best result you’d need to remove the door sills clean and prep the area before wrapping. That way there’ll be no edge visible and in fact, you won’t have to get the edge perfect as the sills will hide it.
-
Re: How restore deep satin black between cab windows ?
Armour all
Despite thousands of "restore, trim rubber etc." on the market, every single one i have tried leaves streaks
-
Super Member
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
-
Regular Member
Re: How restore deep satin black between cab windows ?
Folks, I really appreciate all the helpful suggestions !
Originally Posted by Eldorado2k
There’s 2 ways to fix that. Either the D166 itself can do it, or it’s that non porus plastic..
If it’s made of that non porus plastic, the best way to restore it back to new is to use a paint cleanser like McKee’s Coating Prep Polish.
Here’s what the non porus plastic on my fathers 2004 Toyota Tacoma looked like.
Coating Prep Polish. Applied with a terry microfiber applicator [you can also use a wet Magic Eraser with the polish]
After.
Restored it to brand new condition.
That’s not some cover up product that will fade away in a couple of weeks... That’s how it really looked on its own because it was truly restored.
The restoration on that '04 Tacoma is absolutely great. I have some D166, but think I need to try the McKees coating prep. I'm looking forward to getting this fixed. Thanks again, I really value all of the free sharing experiences folks here so willingly provide
Rick......(Spelled with a "D" )
-
Post Thanks / Like - 1 Thanks, 1 Likes, 0 Dislikes
-
Super Member
Re: How restore deep satin black between cab windows ?
What is the original finish? Is it matte? If it is then don’t polish it unless you want that gloss look. Once polished you will lose that matte look for good.
-
Regular Member
Re: How restore deep satin black between cab windows ?
Originally Posted by The Guz
What is the original finish? Is it matte? If it is then don’t polish it unless you want that gloss look. Once polished you will lose that matte look for good.
It isn't matte, rather smooth and satin, but no substantial gloss, so I'm thinking about doing a very small test spot. Unfortunately there isn't an inconspicuous place since they're at eye level.
Rick......(Spelled with a "D" )
-
Super Member
How restore deep satin black between cab windows ?
I’d be more cautious with applying the wrong kind of trim restoring product than I would be with polishing it. If it’s what it looks like, no trim restoring product will work any good and if anything could have an adverse effect.
Originally Posted by Chevota Guy
It isn't matte, rather smooth and satin, but no substantial gloss, so I'm thinking about doing a very small test spot. Unfortunately there isn't an inconspicuous place since their at eye level.
You can do a test spot.. Just lay down some tape to where you leave a nice thin straight strip for you to test on. Best way is to go thick on the tape on both sides so it leaves you all the room to do your thing while staying within the tape lines. Then once you remove the tape even if it turned out less than stellar, at least it’s only a thin perfectly straight strip going across the trim.
Similar Threads
-
By CMHMHH in forum Ask your detailing questions!
Replies: 5
Last Post: 10-24-2020, 07:07 AM
-
By bcgreen in forum Tricks, Tips and Techniques
Replies: 2
Last Post: 07-28-2018, 09:35 PM
-
By Maestro Sam in forum Auto Detailing 101
Replies: 9
Last Post: 11-14-2016, 07:06 PM
-
By Regency in forum Auto Detailing 101
Replies: 5
Last Post: 11-30-2014, 01:43 AM
-
By SON1C in forum Auto Detailing 101
Replies: 10
Last Post: 04-29-2012, 09:25 PM
Members who have read this thread: 0
There are no members to list at the moment.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
S |
M |
T |
W |
T |
F |
S |
28 | 29 | 30 |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
31
| 1 |
|
Bookmarks