-
Super Member
Re: Forced Rotation VS Free Spinning...
Originally Posted by
dcjredline
IMO free spinning is pretty worthless in general with the curves and contours of newer freaking vehicles. Just did a 2012 Cruze and unless you have a every pad in 1 inch increments you will stall all over the place. The only thing free spin is good for are flat panels such as the roof. Ive barely touched my GG6 since getting the 3401.
I couldn't disagree with this more.
With the right technique, the GG6 (or any free-spinning machine) is more than capable of correction on curved panels.
It is no coincidence that man's best friend cannot talk.
-
Post Thanks / Like - 0 Thanks, 1 Likes, 1 Dislikes
-
Re: Forced Rotation VS Free Spinning...
i agree with Paul. Any time my GG6 stalls is when my technique is less than perfect. Mostly it's when I only have a very small area to do, and I don't take the time to switch backing plates so I can go to a smaller pad. But that's not the machine's fault.
I will be purchasing a gear driven machine in the not too distant future, but it is certainly not because the free spinning DA doesn't do the job.
-
Post Thanks / Like - 0 Thanks, 0 Likes, 1 Dislikes
-
Re: Forced Rotation VS Free Spinning...
So, I've been researching the Makita PO5000C and to my surprise, there are a number of people complaining that it stalls much too easily in free-spin mode. Certainly experience and technique can play a role here. However, for a 7.5Amp machine to be getting numerous complaints of stalling is disappointing!
-
Super Member
Re: Forced Rotation VS Free Spinning...
Pressure causes stalling. If you watch a Rupes “how to” video you will see that very little pressure is used or needed. Technique is the key to minimize stalling. With the advancement of abrasive technology and pad technology less pressure is needed to get perfect results. If you are worried about stalling just buy a rotary and don’t worry about stalling anymore.
-
Post Thanks / Like - 0 Thanks, 3 Likes, 0 Dislikes
-
Re: Forced Rotation VS Free Spinning...
Originally Posted by
rlmccarty2000
Pressure causes stalling. If you watch a Rupes “how to” video you will see that very little pressure is used or needed. Technique is the key to minimize stalling. With the advancement of abrasive technology and pad technology less pressure is needed to get perfect results. If you are worried about stalling just buy a rotary and don’t worry about stalling anymore.
Some are saying that the Makita, on speed setting "4" in free spinning mode, will pretty much stall under the weight of itself! That does seem pretty bad. We all know how important technique is when using a free spinning machine. It just seems that the Makita is getting a disproportionate number of bad reviews with regard to its performance in free spinning mode. For comparison, I haven't heard nearly the same complaints for the GG15 or 21. Or any other comparable machine which are free spinning only!
-
Super Member
Re: Forced Rotation VS Free Spinning...
Originally Posted by
rlmccarty2000
Pressure causes stalling. If you watch a Rupes “how to” video you will see that very little pressure is used or needed. Technique is the key to minimize stalling. With the advancement of abrasive technology and pad technology less pressure is needed to get perfect results. If you are worried about stalling just buy a rotary and don’t worry about stalling anymore.
Exactly.
It is no coincidence that man's best friend cannot talk.
-
Post Thanks / Like - 0 Thanks, 0 Likes, 1 Dislikes
-
Re: Forced Rotation VS Free Spinning...
I completely agree that technique is key. I guess I am interpreting the negative reviews on the Makita to mean that for a 7.5 amp machine, it is stalling way too often.
For those that have actually used the Makita PO5000C, and something similar, say the Grio'ts BOSS G15 (also a 7.5amp motor), how does the Makita compare in terms of free-spin power? Does it stall (in free-spin) much more than the GG G15?
-
Post Thanks / Like - 0 Thanks, 0 Likes, 1 Dislikes
-
Super Member
Re: Forced Rotation VS Free Spinning...
Originally Posted by
Sonic Pilot
I completely agree that technique is key. I guess I am interpreting the negative reviews on the Makita to mean that for a 7.5 amp machine, it is stalling way too often.
For those that have actually used the Makita PO5000C, and something similar, say the Grio'ts BOSS G15 (also a 7.5amp motor), how does the Makita compare in terms of free-spin power? Does it stall (in free-spin) much more than the GG G15?
I have both the 5000C and the G15. The 5000c must be run on speed 5, it's highest setting to NOT stall under its own weight. 5 on the 5000C is like 2 on the G15. G15 runs circles around it in free spin mode. No pun intended.
If you buy the 5000C do so as a gear driven machine. You will likely never use it in free spin mode other than minor correction or to spread product.
ScottH
-
Re: Forced Rotation VS Free Spinning...
Originally Posted by
ScottH
I have both the 5000C and the G15. The 5000c mist be run on speed 5, it's highest setting to NOT stall under its own weight. 5 on the 5000C is like 2 on the G15. G15 runs circles around it in free spin mode. O pun intended.
ScottH
Hmmm....very interesting. This is a good comparison. I am surprised to hear that considering they are both 7.5 amp motors. What a shame. Kudos to GG on the BOSS G15!
-
Super Member
Re: Forced Rotation VS Free Spinning...
LOL, I can see there are many a hurt butts here just cause of MY opinion, to the point of never meeting me and slamming my technique. Get over it, just cause you like the long throw doesnt mean everyone has to. OMG people. This is what always happens when we have to discuss this subject, the babies come out of the wood work when you insult their precious long throw. You like what you like and I (and a few others obviously feel the same) like what I like. Insulting me (us) isnt going to change our minds ha ha ha ha ha ha ha ha ha ha!!!!!!!!!!!! Funny to log on and see all this today. SMH
"Dirt likes detergent so much better than the surface that it's attached to, it'll leave that surface to go hang out with the soap"...
aim4squirrels
-
Post Thanks / Like - 0 Thanks, 1 Likes, 3 Dislikes
Bookmarks