Thanks: 0
Likes: 0
Dislikes: 0
-
Super Member
Got my home-crafted cart operational
Since it rained most of the holiday weekend, I used some of my idle time to get my homemade detail cart far enough along to be functional.
I had originally planned on buying and modifying a three-shelf cart from HF, but when a friend offered me a couple 24x17 inch aluminum pans and lengths of 1 inch angle, I took to the garage to build it all from stuff I had lying around.
The base is a piece of coated hardboard, with some short 2x4 blocks screwed to the corners, both to mount the casters and the uprights. The bottom compartment, dedicated to MF storage, is walled on three sides with storm-window plexiglass to keep 'em clean. I haven't decided on a front door yet, so I just have a clear curtain in place, weighted by a wooden dowel at the bottom. Dividers cut from foam signboard keeps the stacks separated into three categories: premium, mid-grade and utility.
The center shelf, lined with rubber mesh shelf liner, has canisters filled with applicator pads and a tray for gloves and finger pockets tucked to the sides, leaving a lot of space for a polisher or two.
In the upper compartment, also lined with rubber mesh, I hung a piece of aluminum flashing over one side to which I had glued a bunch of plastic pipe scraps as brush holders. Across the back and opposite side, I cut a few pieces from a heavy 4 inch mailing tube and attached them with binder clips to hold spray bottles, clay bars in baggies or even tuck in mf towels to keep them segregated while in use.
In theory, it should serve my needs well, but I'm sure a test drive or two may show where any revisions or improvements are needed. Since I had so much of the odds and ends already in stock, total construction cost was less than $25.
Thanks for viewing.
For those who have worked off something similar, any ideas for improvement?
Bill
-
Super Member
Re: Got my home-crafted cart operational
Very cool cart Bill.......you need a handle on that puppy to push it around.
Some good innovation there.
Tim "I have done so much with so little for so long. Now I can do anything with nothing"
-
Super Member
Re: Got my home-crafted cart operational
Originally Posted by BillyJack
Thanks for viewing.
For those who have worked off something similar, any ideas for improvement?
Bill
A place for everything, and everything in its place.
Ingenious and thrifty
Might look into adding plexiglass to mine also.
Thanks for posting.
I found it necessary to add tubular foam insulation tubes, wire-tied to the verticle angle pieces in an effort to paint-safe my all metal detailing cart.
VT
Originally Posted by glen e
....It's all I use these days....they are buffing when I'm relaxing...and still don't get the powder out of canines!
-
Super Member
Re: Got my home-crafted cart operational
Originally Posted by Vegas Transplant
A place for everything, and everything in its place.
Ingenious and thrifty
Might look into adding plexiglass to mine also.
Thanks for posting.
I found it necessary to add tubular foam insulation tubes, wire-tied to the verticle angle pieces in an effort to paint-safe my all metal detailing cart.
Very good idea.......
How you been VT?
Tim "I have done so much with so little for so long. Now I can do anything with nothing"
-
Super Member
Re: Got my home-crafted cart operational
Cool Tim
I didn't have a choice since few of my then-customers had level driveways.
Good to see ya still holding down both AGO & the Queen City
VT
Originally Posted by glen e
....It's all I use these days....they are buffing when I'm relaxing...and still don't get the powder out of canines!
-
Super Member
Re: Got my home-crafted cart operational
Scott Harle
Autodermatology
#autodermatology
-
Very nice. I like the towel storage. Overall you can't beat it for the price. I'd buy one.
-
Super Member
Re: Got my home-crafted cart operational
Similar Threads
-
By WAXOFF in forum Auto and Garage Accessories
Replies: 16
Last Post: 06-30-2013, 07:24 PM
-
By CheckeredFlag in forum Auto and Garage Accessories
Replies: 3
Last Post: 06-17-2013, 11:01 AM
-
By nissenc1337 in forum Auto Detailing 101
Replies: 13
Last Post: 05-08-2013, 08:04 AM
-
By hoyt66 in forum Off-Topic
Replies: 5
Last Post: 09-16-2012, 01:29 PM
-
By tw33k2514 in forum Auto Detailing 101
Replies: 28
Last Post: 10-22-2011, 10:01 AM
Members who have read this thread: 0
There are no members to list at the moment.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
S |
M |
T |
W |
T |
F |
S |
31 |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
| 1 | 2 | 3 | 4 |
|
Bookmarks