Dislikes: 0
-
Which buffing pads for the FLEX XCE 10-8 Supa Beast?
Which buffing pads for the FLEX XCE 10-8 Supa Beast?
Anytime I get questions via e-mail, a PM or a FB message I prefer to invest my typing time where
A: It's easier for me to share links, pictures and videos.
B: More people can read and thus benefit from the information. (no just one set of eyeballs)
The reality is, most people that contact me found me via an article I've written or a reply I've written on this forum. The thing is, instead of figuring out that the whole reason they are contacting me is because they found me via an article or answer I wrote on the forum that they to should bring their question to the forum because not only will that help them.... but it will help a future "them". If I answer everything in a private e-mail or other touch point, no one would find and contact me. It's a cycle or pattern that repeats as long as everything is shared in the public domain.
The above is kind of wordy but re-read it slowly and it will make sense.
So I get an e-mail asking,
Hey Mike!
I was gifted the new Flex XCE 10-8 “Supa Beast” for Christmas and I wanted to pick your brain.
I am an avid user of the rotary and the free spinning Rupes orbital machines. I know with the 3401, the “fan favorite” foam pads were the LC Force Hybrid pads which are thick.
Do you find that these are still generally the most comfortable option (regarding user experience) on the XCE 10-8 as they were on the 3401, or would you prefer something like the Buff ‘n Shine Uro-Tec pads - or maybe even thin Mille pads? What would your choice of wool pad be - something like the rupes DA wool or the LC purple wool?
Thank you!
Great questions!
I've probably used the new Supa BEAST as much or more than anyone since I've had it longer than anyone, at least in the U.S.A.
Here's my take and preference.
First - Because it's basically an updated version of the traditional BEAST, that is a corded 8mm gear-driven orbital polisher without the aluminum housing. So with the CORDED version I LIKE and PREFER the 6" backing plate so I can turn and churn the 6.5" Lake Country Force Hybrid Foam Pads. And "yes" these are thick foam pads but a gear-driven tool don't care what kind of pad you put on it because it's gear-driven.
And then get some Lake Country 6.5" Force Hybrid pads.
Lake Country Hybrid Power Finish 6.5 Inch Pads
I can plow through just about any project with a collection of,
Orange
White
Black
Mostly the orange and white.
Tool Action Transfer
I've seen people make the argument that a thinner pad transfers the action of the tool to the surface of the paint better and I believe it and agree with it but in the BIG PICTURE of car detailing, you put a foam cutting pad on the Supa BEAST and use a quality compound, crank it up to the 6 speed setting and any defect that should be removed is going to be removed regardless of how thick or thin the pad is. PLUS in my experience, for the same reason a thin pad transfers the action of a gear-driven tool to the surface better it also tends to yank you around better. One step forward, one step back.
Now if you're going to use the 5" backing plate, then at this time any of the 5.5 and 6" pads from LC, B&S, RUPES and Griot's work great.
Hope that helps...
Hope that helps and feel encouraged to join our forum, this is where I answer questions. Email and Facebook messaging are okay, but the forum is a LOT more powerful. (think about it - it's how you found me in the first place)
Click here to join the AutogeekOnline.net car detailing discussion forum - THE best forum on the Internet
(the above is just a template that is now a sticky so each time someone sends me an e-mail or FB message I don't have to search for an older reply I wrote to get the formatted text above, I have it here in this sticky.
As I say... I always type for the future.... never just the present...
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
-
Re: Which buffing pads for the FLEX XCE 10-8 Supa Beast?
More....
Here's my article on doing the backing plate swap for the Supa BEAST
Supa BEAST backing plate swap
And I recently wrote this article for foam buffing pads for the new Griot's G9 - the pads shown here would be a good choice for the 5" backing plate on the Supa BEAST.
Foam Pad Options for the Griots G9 Polisher
Also note - I'm testing some pads for the 5" backing plate on the Supa BEAST and the CBEAST.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
-
Newbie Member
Re: Which buffing pads for the FLEX XCE 10-8 Supa Beast?
Hey Mike! Jordan here (who sent you the email) - thank you for taking the time to write a post up about this! I am not much for forums, but maybe in the future I can be more active here with any questions & whatnot.
I got to play with the machine for about 20 minutes last week, using a 5.5" LC Force Hybrid Orange foam and then a normal thickness Rupes Yellow foam. I can honestly say that with the Orange LC Force Hybrid, it was one of the worst, most uncomfortable polishing experiences I have ever had. I was keeping the pad as flat as I could, tried it at multiple speeds, and was using the Rupes Mille Fine polish which as you know was designed for gear driven movement. I made it through half of the hood and I was already wanting to sell it. I then swapped to the slightly thinner (1/4" thinner I believe?) Rupes Yellow foam and my experience was significantly improved, however still not great.
Admittedly, I am not much of a forced rotation user. I love my rotary polishers (DeWalt, Flex, and Rupes) for sanding mark removal and for an aggressive first cut when needed - and I use my Rupes 21 Mark II / Flex XFE 7-12 80 / iBrid Nano for all else. I do own a Mille, and in my opinion/experience it is much smoother than the 3401, but I never reach for it over my random orbitals unless it is a very curvaceous vehicle or I am trying to dial in some edgework.
As disappointed as I was, I played with my XCE again tonight for about two hours, and I now enjoy the machine much more. This time, I tried it with an LC Low Lint Lambswool pad paired with some Griot's Fast Correcting Cream, and the walking was much easier to control. Fairly comfortable - not as much as my rotary or random orbitals - but very manageable. I then followed up using what you suggested - a Griot's Perfecting yellow foam pad - paired it with a few small drops of Perfecting Cream, and WOW was it a different machine. So much smoother, lightyears easier to control, and just a much more enjoyable experience all around. I also gave it a go with the Mille foams/Mille Fine polish, and an HDO Orange foam with some Sonax Perfect Finish - all of which were very smooth.
Everyone's mileage may vary - I certainly don't have the experience with this machine (or likely any machine, for that matter ) that you do. I can say though, that the Force Hybrid pads - at least the denser orange - is NOT for me. Although the powerful forced rotation has zero issue churning anything you put on it, it was a completely different machine when used with thinner (and slightly softer) pads.
I am happy I own this XCE now - it is smoother and more comfortable to me than the 3401 by far. I will just have to stick to the thin pads I guess.
Just my $.02 and personal experience here. Great machine and from an avid Rupes & Flex user, seems like another home run for Flex.
Thanks again, Mike Very much appreciated.
-
Re: Which buffing pads for the FLEX XCE 10-8 Supa Beast?
Originally Posted by Gloss Garage Detail
Hey Mike! Jordan here (who sent you the email) - thank you for taking the time to write a post up about this! I am not much for forums, but maybe in the future I can be more active here with any questions & whatnot.
Hi Jordan,
Thank you for joining the forum. Thank you also for understanding why I prefer to answer question on the forum. It takes a little time to type out helpful info and I prefer to share it with thousands of eyeballs over the decades versus type out a reply in an e-mail where only one set of eyeballs will see the answer.
Originally Posted by Gloss Garage Detail
I got to play with the machine for about 20 minutes last week, using a 5.5" LC Force Hybrid Orange foam and then a normal thickness Rupes Yellow foam. I can honestly say that with the Orange LC Force Hybrid, it was one of the worst, most uncomfortable polishing experiences I have ever had. I was keeping the pad as flat as I could, tried it at multiple speeds, and was using the Rupes Mille Fine polish which as you know was designed for gear driven movement. I made it through half of the hood and I was already wanting to sell it. I then swapped to the slightly thinner (1/4" thinner I believe?) Rupes Yellow foam and my experience was significantly improved, however still not great.
Admittedly, I am not much of a forced rotation user. I love my rotary polishers (DeWalt, Flex, and Rupes) for sanding mark removal and for an aggressive first cut when needed - and I use my Rupes 21 Mark II / Flex XFE 7-12 80 / iBrid Nano for all else. I do own a Mille, and in my opinion/experience it is much smoother than the 3401, but I never reach for it over my random orbitals unless it is a very curvaceous vehicle or I am trying to dial in some edgework.
As disappointed as I was, I played with my XCE again tonight for about two hours, and I now enjoy the machine much more. This time, I tried it with an LC Low Lint Lambswool pad paired with some Griot's Fast Correcting Cream, and the walking was much easier to control. Fairly comfortable - not as much as my rotary or random orbitals - but very manageable. I then followed up using what you suggested - a Griot's Perfecting yellow foam pad - paired it with a few small drops of Perfecting Cream, and WOW was it a different machine. So much smoother, lightyears easier to control, and just a much more enjoyable experience all around. I also gave it a go with the Mille foams/Mille Fine polish, and an HDO Orange foam with some Sonax Perfect Finish - all of which were very smooth.
Everyone's mileage may vary - I certainly don't have the experience with this machine (or likely any machine, for that matter ) that you do. I can say though, that the Force Hybrid pads - at least the denser orange - is NOT for me. Although the powerful forced rotation has zero issue churning anything you put on it, it was a completely different machine when used with thinner (and slightly softer) pads.
I am happy I own this XCE now - it is smoother and more comfortable to me than the 3401 by far. I will just have to stick to the thin pads I guess.
Just my $.02 and personal experience here. Great machine and from an avid Rupes & Flex user, seems like another home run for Flex.
Thanks again, Mike Very much appreciated.
Actually, I'm not a fan of the smaller 5.5" Force Hybrid pads on any of the FLEX gear-driven tools. It's too thick and squatty. I don't find the tool easy to guide and buff with using this shape of pad. If using a 5" backing plate on any of the gear-driven FLEX tools I much prefer the thinner LC HDO, SDO pads, the B&S Uro-Tech pads and "yes" the RUPES 6" foam pads, (using RUPES anything on a non-RUPES tool is called co-mingling and a hex be on my head)
On the CORDED BEASTS - I do like and prefer the 6.5" LC Force Hybrid pads. Larger 6.5" pads from B&S, LC and yes, RUPES also work great but the BEASTS will be hard on RUPES pads. I'm sure it's nothing personal.
If you send me your shipping address, I'll send you the larger backing plate for your Supa BEAST and some 6.5" LC Force Hybrid pads to test out.
I will say however - that the BEAST and the Supa BEAST are in fact BEASTS and no one becomes an expert or even comfortable or proficient until they buff out some cars or as I like to say,
Spend some time behind the tool...
It's true I have years of hours behind most tools and I can in fact make them all dance on paint, but I paid the price to get here, the price of time in the garage and in most cases, making other people's cars shine.
Stick with her, she's a power friend and asset when it comes to taking a diamond in the rough and turning it into a glistening gemstone....
-
Post Thanks / Like - 0 Thanks, 2 Likes, 0 Dislikes
-
Newbie Member
Re: Which buffing pads for the FLEX XCE 10-8 Supa Beast?
Mike, thank you and you’re welcome for replying here! It makes perfect sense, write ups and Facebook posts have helped me in the past so if this could help someone else even a little bit, I’m all for it.
That is interesting regarding the 5.5” Force pads, I would imagine they would cause less walk but then again, I am not familiar with these units
That is INCREDIBLY kind of you to do that - I will email you my shipping address and try them out ASAP, and report back here. I cannot thank you enough for that!!
This machine is absolutely a “Supa Beast” - I am thankful I have it and I look forward to more time behind it!
Happy New Year!!
-
Re: Which buffing pads for the FLEX XCE 10-8 Supa Beast?
Originally Posted by Gloss Garage Detail
Mike, thank you and you’re welcome for replying here! It makes perfect sense, write ups and Facebook posts have helped me in the past so if this could help someone else even a little bit, I’m all for it.
Copy that...
That is interesting regarding the 5.5” Force pads, I would imagine they would cause less walk but then again, I am not familiar with these units.
Just too thick in my experience for the diameter and the shape of the pad. They are too cylindrical. They would work better if they had some taper to them like the originals.
Originally Posted by Gloss Garage Detail
That is INCREDIBLY kind of you to do that - I will email you my shipping address and try them out ASAP, and report back here. I cannot thank you enough for that!!
This machine is absolutely a “Supa Beast” - I am thankful I have it and I look forward to more time behind it!
Will ship out today.
-
Newbie Member
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
Diner thanked for this post
-
Re: Which buffing pads for the FLEX XCE 10-8 Supa Beast?
Originally Posted by Gloss Garage Detail
Received the plate and pads today and put the plate on the Supa Beast! Definitely a sizable difference, I look forward to trying it this week as soon as I get the chance.
I wish I could give you a 5 minute lesson in person. I would show you how to make this polisher dance on paint or plow through paint depending on when you need to do.
Don't be afraid to man-handle it. If you need to remove swirls and scratches, hold the pad flat to the surface and PRESS down on it! Make sure YOU control it. If you feel it pulling in any direction then you're not holding the pad flat to the surface. This tool is a true BEAST but YOU have to become the Master and show it who's the boss!
Originally Posted by Gloss Garage Detail
Again, thank you so much Mike. I appreciate it a ton!
I just filled out a "New Product Request" form. Management trusts me and signs-off on it and then the samples are shipped. So thanks be to Autogeek.
AND - if you ever see me teaching a class in your area - attend. You will learn more in my class than 10 years of trying to figure it all out on your own.
-
Post Thanks / Like - 0 Thanks, 2 Likes, 0 Dislikes
-
Super Member
Re: Which buffing pads for the FLEX XCE 10-8 Supa Beast?
After reading these comments and observations, it made me think a little bit what these mentioned influences are, how they are lessened, and had some other thoughts.
Seems Rupes has recognized that issue, and thus formulated special "Mille" Compounds and Polishes to give greater lubricity and longer work time when used with their forced rotation Mille.
Thus, I'm thinking that not only the Pad Size and Type play an influence, but also the Chemicals in use. That some products might be more prone to being grabby, drier, or dry faster in use, a shorter work time, have a tendency to make the user fight with the operations of Compounding and Polishing. Possible?
What about a Pad Conditioner also? Might one reap some improvements in Polishing ease with these products adding lubricity with virtually any Polish-Compound?
-
Super Member
Re: Which buffing pads for the FLEX XCE 10-8 Supa Beast?
Good posts here.
Thanks Mike and Autogeek for the tips and the generosity.
Gloss Garage, thanks for the pics and sharing your experiences.
Myself, on the "old" 3401, I have used 4" Hydro Tech pads on the smaller backing plate, 5.5" pads, and the larger pads on the larger backing plate, as well . They all work pretty good. For the Hydro's, the thicker version seems fine.
Lately, I'm using the 5.5" SDO pads with the ~5" plate and have been enjoying that experience.
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
Similar Threads
-
By Mike Phillips in forum How to articles
Replies: 68
Last Post: 08-24-2022, 05:02 AM
-
By Mike Phillips in forum Product Reviews by Mike Phillips
Replies: 3
Last Post: 02-16-2021, 01:00 PM
-
By Mike Phillips in forum How to articles
Replies: 3
Last Post: 12-31-2020, 02:28 PM
-
By Mike Phillips in forum Ask your detailing questions!
Replies: 9
Last Post: 12-04-2019, 07:35 PM
-
By Justin at Final Inspection in forum Auto Detailing 101
Replies: 9
Last Post: 12-03-2019, 05:09 AM
Members who have read this thread: 2
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
S |
M |
T |
W |
T |
F |
S |
31 |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
| 1 | 2 | 3 | 4 |
|
Bookmarks