I'm polishing a '63 Continental this weekend - could use some tips! [first post]

[crg001]

I'm polishing a '63 Continental this weekend - could use some tips! [first post] (https://www.autogeekonline.net/forum/ask-mike-phillips-your-detailing-questions-/128679-im-polishing-63-continental-weekend-could-use-some-tips-first-post.html)



Hi Mike and everyone on AGO!

Long time lurker on these forums, first time poster. I've been learning a ton from reading articles and forum posts and have been putting them to what I believe are really excellent results. I've been doing more and more of other people's vehicles and I feel I'm really getting great results polishing using a DA. However, single stage paint is still new to me and one of my friends is trusting me to polish his 1963 Lincoln Continental.

This car has definitely been repainted at some point in it's life with a single stage, and it's not the best quality respray. My friend believes it was done some time in the '90s. Another friend did a test spot on the trunk to see what results they could get using a 15mm DA and foam pads with (a non AG) polish and compound. Here's some pics of the vehicle and the aforementioned test panel. The results they got on the trunk is what he would like to see over the entire vehicle, and I believe I can do that or better.

72712 72713
72714 72715

Products I will be using are a Griot's G9, and my assortment of pads include 5+ each of B&S Uro-Fiber and yellow Uro-Tec, orange and yellow Griot's Boss, and green B&S flat pads. My polishes I plan to use are 3D ACA 500 with Uro Fiber or orange pads for the initial cut and then finish with 3D Speed (and top with 3D Express Wax) on the green or yellow pads, but first I will perform my own test spots. I also have Griot's Correcting Cream and 3D ACA 520 if the ACA 500 is too aggressive. I realize I could just one-step it with Speed, and I will try a test spot doing so, but my expectation is that it will not cut through the oxidation and imperfections well enough, as there are some deeper scratches and swirls in the paint.



My plan is to waterless wash it then clay before beginning.

I have some concerns about the paint quality around some spots so I plan to tape off the rough areas with delicate painter's tape and avoid them. See pics below.

72716 72717



There's also a small bubble on the hood that feels hard to the touch. I'm not sure if this is a thick glob of overspray paint or an actual air bubble underneath the paint and I'm not sure what to do about that. It crossed my mind to sand it down but I'd prefer not to overly abrade this paint.

72718


I've read the articles about doing a Meguiar's #7 restoration on old single stage paints including this one using 3D AAT products,

The Secret to Removing Oxidation and Restoring a Show Car Finish to Antique Single Stage Paints (https://www.autogeekonline.net/forum/how-to-articles-by-mike-phillips/25304-secret-removing-oxidation-restoring-show-car-finish-antique-single-stage-paints.html)

How to restore a Barn Find - 1969 Ford Thunderbird - #7 Rub Out + FLEX = 3D products (https://www.autogeekonline.net/forum/product-reviews-by-mike-phillips/127081-how-restore-barn-find-1969-ford-thunderbird-7-rub-out-flex-3d-products.html))

But time with the vehicle will be limited and this resprayed paint appears to be very thick.

Should I be concerned about starting with 3D ACA 500 compound and microfiber or orange pad without doing a #7 wipe down initially? Would it be worth the time to wipe on some #7 over the entire vehicle and then immediately wipe it off, and begin the correction process?

I'm a little nervous about this one, but I've never been so excited to polish a car before!

Thanks!

-Colin

[Mike Phillips]

Hi Colin,

Welcome to AGO! :welcome:

Cool car to polish out.


After any of my detailing classes, like this one this last weekend

Pictures: 2021 Boat Detailing Class - SOLD OUT! (https://www.autogeekonline.net/forum/pictures-2-day-boat-detailing-classes/128660-pictures-2021-boat-detailing-class-sold-out.html)


The Boss gives me a couple of days off to recoup, recharge and take care of life.


I'll be back in the office and will reply in-depth tomorrow.


:cheers:

[crg001]

Thank you, Mike! I look forward to your reply!

[2black1s]

I'll let Mike give you his take on the polishing aspect but I can share a little on the paint defects you mention.

The area around what I believe is the hood ornament and the antenna where the paint is peeling is probably the result of:
- Not removing the trim during the paint prep
- Not sanding the area right up to the edge

This is a very common defect in low to mid range paint jobs. Removing all trim is the right way... But it adds quite a bit of cost to the job and aside from specialty shops most production paint shops simply mask the trim. Then to compound the problem it is a time consuming and tedious hand operation to sand right to the edge. Again most production shops simply don't take that time. They DA sand as best they can and call it good enough. As you can see, it's not good enough.

That said, I don't think you have a lot to worry about polishing around those areas. The paint that has lost adhesion and is peeling has most likely reached the boundary of the poor sanding and it's unlikely that it will continue peeling much farther.

What I might do if I were in your shoes is chip away the peeling paint by carefully probing with a single edge razor blade and then do a brush touch up of those areas.

As for the blob on the hood, that's a crapshoot trying to determine what it might be. But if it feels solid then it's not a air bubble under the paint. If that were the case you could compress it and it probably would have chipped away by now. It could be a solid drop of paint or it could be corrosion forming beneath the paint. It's really hard to tell from the pic. I'd probably do a little razor blade probing there too.

Have fun... That's a cool car to be working on.

[fly07sti]

The advice that I give you is to work clean. Don’t do too many section passes with your cutting stage. 2-3 passes and clean out your pads with a brush or even better, compressed air after every section. The pads lid of with residue very quickly. The more pads the better. That’s a lot of real estate on that car, so don’t overthink it. Just focus on your technique and working clean and enjoy turning that paint from matte to gloss.

[Mike Phillips]

Hi Mike and everyone on AGO!

Long time lurker on these forums, first time poster.




Thanks for joining! :welcome:








I've been learning a ton from reading articles and forum posts and have been putting them to what I believe are really excellent results. I've been doing more and more of other people's vehicles and I feel I'm really getting great results polishing using a DA. However, single stage paint is still new to me and one of my friends is trusting me to polish his 1963 Lincoln Continental.



Single stage is no big deal, you'll end up treating it like any other paint. There are a few other considerations but nothing out of the realm of what you can already do.







This car has definitely been repainted at some point in it's life with a single stage, and it's not the best quality respray. My friend believes it was done some time in the '90s. Another friend did a test spot on the trunk to see what results they could get using a 15mm DA and foam pads with (a non AG) polish and compound. Here's some pics of the vehicle and the aforementioned test panel. The results they got on the trunk is what he would like to see over the entire vehicle, and I believe I can do that or better.





Before and After looks great!

https://www.autogeekonline.net/forum/attachments/ask-mike-phillips-your-detailing-questions-/72714d1615404880-im-polishing-63-continental-weekend-could-use-some-tips-first-post-20210308_181254-jpg







Products I will be using are a Griot's G9, and my assortment of pads include 5+ each of B&S Uro-Fiber and yellow Uro-Tec, orange and yellow Griot's Boss, and green B&S flat pads.



My guess is ANY FIBER pad will cut great but also leave micro-marring in the paint. That's what fibers do to soft paint and except for white single stage paint, pretty much all other colors of single stage paint will be considered soft.

See my article here,

Fibers are a form of abrasive - Foam Pads vs Microfiber Pads by Mike Phillips (https://www.autogeekonline.net/forum/how-to-articles-by-mike-phillips/126010-fibers-form-abrasive-foam-pads-vs-microfiber-pads-mike-phillips.html)




And here's a more recent article where I think the pictures tell the story.

Foam vs Fiber - Car Detailing by Hand or Machine (https://www.autogeekonline.net/forum/how-to-articles-by-mike-phillips/128316-foam-vs-fiber-car-detailing-hand-machine.html)

http://www.autogeekonline.net/gallery/data/4164/Foam_vs_Fiber_05.JPG











My polishes I plan to use are 3D ACA 500 with Uro Fiber or orange pads for the initial cut and then finish with 3D Speed (and top with 3D Express Wax) on the green or yellow pads, but first I will perform my own test spots.




My guess is the above process will work great. BUT - be sure to do the Test Spot and inspect the results from the microfiber pad closely. You may be able to get the same correction results using a foam cutting pad and avoid micro-marring the paint. Only testing will show.

By the way, 3D makes GREAT abrasive technology. Here's my article on this topic. I talk more about this topic than any other related topic to car detailing.


Abrasive Technology - THE most important factor when it comes to polishing paint (https://www.autogeekonline.net/forum/2018-new-car-detailing-how-to-article-by-mike-phillips/120326-abrasive-technology-most-important-factor-when-comes-polishing-paint.html)









I also have Griot's Correcting Cream and 3D ACA 520 if the ACA 500 is too aggressive. I realize I could just one-step it with Speed, and I will try a test spot doing so, but my expectation is that it will not cut through the oxidation and imperfections well enough, as there are some deeper scratches and swirls in the paint.



3D Speed is an amazing one-step product. If it were me, I would actually test using the 3D Speed First.

Sometimes I 2-step a car using a one-step product. I make the correction step using a foam cutting pad and follow with the same product only now using a foam polishing pad. It just depends on what I'm trying to do and also what I'm being paid. But when it comes to classics like this - I will tend to do more work than I'm being paid as it's in my nature. I appreciate classics, muscle cars and streetrods, modern cars are like Bic Lighters - once they are empty you throw them away or trade them in on the next Bic Lighter. For this reason, it's hard to be passionate about [most] modern cars.







My plan is to waterless wash it then clay before beginning.

I have some concerns about the paint quality around some spots so I plan to tape off the rough areas with delicate painter's tape and avoid them. See pics below.




I would take John aka 2black1s advice for the chipping and peeling paint. With cars like this - it simply is what it is. Do your best, educate your customer and move on.

https://www.autogeekonline.net/forum/attachments/ask-mike-phillips-your-detailing-questions-/72717d1615405520-im-polishing-63-continental-weekend-could-use-some-tips-first-post-20210308_182155-jpg







There's also a small bubble on the hood that feels hard to the touch. I'm not sure if this is a thick glob of overspray paint or an actual air bubble underneath the paint and I'm not sure what to do about that. It crossed my mind to sand it down but I'd prefer not to overly abrade this paint.




https://www.autogeekonline.net/forum/attachments/ask-mike-phillips-your-detailing-questions-/72718d1615406058-im-polishing-63-continental-weekend-could-use-some-tips-first-post-20210308_181138-2-jpg

If it were me? I'd carefully machine buff all around it and then lightly buff over it and call it good. Don't turn a mole hill into a mountain.

http://www.autogeekonline.net/gallery/data/715/Molehill_into_Mountain.jpg








I've read the articles about doing a Meguiar's #7 restoration on old single stage paints (including this one using 3D AAT products

The Secret to Removing Oxidation and Restoring a Show Car Finish to Antique Single Stage Paints (https://www.autogeekonline.net/forum/how-to-articles-by-mike-phillips/25304-secret-removing-oxidation-restoring-show-car-finish-antique-single-stage-paints.html)

How to restore a Barn Find - 1969 Ford Thunderbird - #7 Rub Out + FLEX = 3D products (https://www.autogeekonline.net/forum/product-reviews-by-mike-phillips/127081-how-restore-barn-find-1969-ford-thunderbird-7-rub-out-flex-3d-products.html)),

but time with the vehicle will be limited and this resprayed paint appears to be very thick. Should I be concerned about starting with 3D ACA 500 compound and microfiber or orange pad without doing a #7 wipe down initially? Would it be worth the time to wipe on some #7 over the entire vehicle and then immediately wipe it off, and begin the correction process?

I'm a little nervous about this one, but I've never been so excited to polish a car before!

Thanks!

-Colin


My how-to articles for #7 are mostly for original and antique single stage paints. The paint on a car from 1990 would qualify as antique by most car guys standards, which is usually 20 or 25 years old.


From the look of the results on the trunk lid, if it were me and time was limited, I would test out the 3D Speed with a foam cutting pad. See what you get. A foam cutting pad can leave marring in and of itself so if you use a foam cutting pad, inspect for marring. You could always cut with fiber and re-polish with foam using the 3D Speed instead of a dedicated compound. The cool benefit to 3D Speed is great performance and easy wipe-off.


Just do some testing...


:)

[Mike Phillips]

One more...


I don't recommend this technique for everyone, but it does work.


The COMET Technique by Mike Phillips - 1965 Cadillac - Original Single Stage Paint - Slam job by Mike Phillips (https://www.autogeekonline.net/forum/ask-mike-phillips-your-detailing-questions-/120124-comet-technique-mike-phillips-1965-cadillac-original-single-stage-paint-slam-job-mike-phillips.html)


The COMET Technique for oxidized single stage paint

http://www.autogeekonline.net/gallery/data/3726/1965_Caddy_018.JPG

NOTE: The COMET technique is ONLY for oxidized SINGLE STAGE paint.

Do no try this on a modern clearcoat paint you will likely scour the finish.


Be sure to read the entire article and towards the end, as in my norm - I took a picture and shared what I used to buff out the car including HOW MANY PADS WERE USED.

Most people don't use enough pads when using foam pads to do correction work or when using an AIO


http://www.autogeekonline.net/gallery/data/3726/SlamJob_001.JPG



:buffing:

[Mike Phillips]

One more...

This last September, we had a RECORD BREAKING class for all kinds of new records. One of the records we broke was how many cars detailed over 3 days. For the September class (https://www.autogeekonline.net/forum/pictures-3-day-car-detailing-bootcamp-classes/127656-pictures-2020-september-3-day-detailing-bootcamp-class.html),

17 cars detailed in 3 days!



Another record we broke was this class was able to detail 3 cars with single stage paint and 2 of the cars had the ORIGINAL paint. The students dug it.

Here's a dedicated article from that class besides the pictures and comments write-up.


1968 Cadillac Original Paint Detailing Class - September 2020 (https://www.autogeekonline.net/forum/pictures-3-day-car-detailing-bootcamp-classes/127808-1968-cadillac-original-paint-detailing-class-september-2020-a.html)


Here's the class using COMET during the Prep Wash.

Find any other class that is photo-documented showing this technique? Bueller?

http://www.autogeekonline.net/gallery/data/4144/800_1968_Cadillac_017.JPG

http://www.autogeekonline.net/gallery/data/4144/800_1968_Cadillac_018.JPG


http://www.autogeekonline.net/gallery/data/4144/800_1968_Cadillac_020.JPG



Final results...

http://www.autogeekonline.net/gallery/data/4144/800_1968_Cadillac_053.JPG

http://www.autogeekonline.net/gallery/data/4144/800_1968_Cadillac_054.JPG


For everyone that will read this into the future, (I always type for the future, not the moment), PLEASE read the entire write-up before using the Comet Technique. There's a lot more involved and this class was under my direction and supervision the entire time. I point this out because I've been there and done this a number of times with single stage paint. It's not for the faint of heart.

1968 Cadillac Original Paint Detailing Class - September 2020 (https://www.autogeekonline.net/forum/pictures-3-day-car-detailing-bootcamp-classes/127808-1968-cadillac-original-paint-detailing-class-september-2020-a.html)



:)

[Mike Phillips]

More...

Also just to note- we MACHINE scrubbed the vinyl top with Comet too....



http://www.autogeekonline.net/gallery/data/4144/800_1968_Cadillac_003.JPG



http://www.autogeekonline.net/gallery/data/4144/800_1968_Cadillac_012.JPG



And here's the link to this photo-documented record breaking class.


Pictures: 2020 September 3-Day Detailing Bootcamp Class (https://www.autogeekonline.net/forum/pictures-3-day-car-detailing-bootcamp-classes/127656-pictures-2020-september-3-day-detailing-bootcamp-class.html)

http://www.autogeekonline.net/gallery/data/4144/1968_Cadillac_061.JPG



:)

[crg001]

I'll let Mike give you his take on the polishing aspect but I can share a little on the paint defects you mention.

The area around what I believe is the hood ornament and the antenna where the paint is peeling is probably the result of:
- Not removing the trim during the paint prep
- Not sanding the area right up to the edge

This is a very common defect in low to mid range paint jobs. Removing all trim is the right way... But it adds quite a bit of cost to the job and aside from specialty shops most production paint shops simply mask the trim. Then to compound the problem it is a time consuming and tedious hand operation to sand right to the edge. Again most production shops simply don't take that time. They DA sand as best they can and call it good enough. As you can see, it's not good enough.

That said, I don't think you have a lot to worry about polishing around those areas. The paint that has lost adhesion and is peeling has most likely reached the boundary of the poor sanding and it's unlikely that it will continue peeling much farther.

What I might do if I were in your shoes is chip away the peeling paint by carefully probing with a single edge razor blade and then do a brush touch up of those areas.

As for the blob on the hood, that's a crapshoot trying to determine what it might be. But if it feels solid then it's not a air bubble under the paint. If that were the case you could compress it and it probably would have chipped away by now. It could be a solid drop of paint or it could be corrosion forming beneath the paint. It's really hard to tell from the pic. I'd probably do a little razor blade probing there too.

Have fun... That's a cool car to be working on.

Thank you so much for the response! This is some very good insight on how this car was resprayed and what caused the peeling edges of the paint. I was afraid to touch those areas, but I will absolutely try chipping away the peeling edges with a razor blade. I think I may leave the blob on the hood alone though, I like Mike's analogy of mountains and molehills for that particular imperfection. Thanks again for your help. I have been following your threads about your deliberation between a Flex and a Mille, and I like your reasonings for choosing the Rupes. I also very much appreciated the tear down photos!

Cheers!

[crg001]

My guess is ANY FIBER pad will cut great but also leave micro-marring in the paint. That's what fibers do to soft paint and except for white single stage paint, pretty much all other colors of single stage paint will be considered soft.

See my article here,

Fibers are a form of abrasive - Foam Pads vs Microfiber Pads by Mike Phillips (https://www.autogeekonline.net/forum/how-to-articles-by-mike-phillips/126010-fibers-form-abrasive-foam-pads-vs-microfiber-pads-mike-phillips.html)




And here's a more recent article where I think the pictures tell the story.

Foam vs Fiber - Car Detailing by Hand or Machine (https://www.autogeekonline.net/forum/how-to-articles-by-mike-phillips/128316-foam-vs-fiber-car-detailing-hand-machine.html)

http://www.autogeekonline.net/gallery/data/4164/Foam_vs_Fiber_05.JPG











My guess is the above process will work great. BUT - be sure to do the Test Spot and inspect the results from the microfiber pad closely. You may be able to get the same correction results using a foam cutting pad and avoid micro-marring the paint. Only testing will show.

By the way, 3D makes GREAT abrasive technology. Here's my article on this topic. I talk more about this topic than any other related topic to car detailing.


Abrasive Technology - THE most important factor when it comes to polishing paint (https://www.autogeekonline.net/forum/2018-new-car-detailing-how-to-article-by-mike-phillips/120326-abrasive-technology-most-important-factor-when-comes-polishing-paint.html)

3D Speed is an amazing one-step product. If it were me, I would actually test using the 3D Speed First.

Sometimes I 2-step a car using a one-step product. I make the correction step using a foam cutting pad and follow with the same product only now using a foam polishing pad. It just depends on what I'm trying to do and also what I'm being paid. But when it comes to classics like this - I will tend to do more work than I'm being paid as it's in my nature. I appreciate classics, muscle cars and streetrods, modern cars are like Bic Lighters - once they are empty you throw them away or trade them in on the next Bic Lighter. For this reason, it's hard to be passionate about [most] modern cars.




Hi Mike, I'm honored to be getting some advice from the greatest on this upcoming project!

Regarding foam vs fiber for the cutting stage, I understand your meaning on how microfiber can cause micro-marring. I did not personally perform the test spot on the trunk so I am not yet familiar with how hard the paint is. I will definitely do some test side by side with that portion starting with the least aggressive approach and work my way up to the microfiber + compound if it's what the paint calls for.

I've read your articles on abrasive technology, and I've since become a huge fan of 3D's products. I watched your video with your segment with Tunch of 3D explaining their manufacturing process and I found that all highly interesting. I can definitely appreciate the fact that these amazing products are responsible for the results I'm able to get as long as I understand their uses!

3D speed is indeed an amazing product, I was on the fence whether I was going to do a dedicated two-step polishing process and then top with a carnauba wax like Collinite 845, but I decided to Speed things up a bit (lol) by combining the wax and finishing polish step into one, as I feel the Montan wax base will also look incredible on the single stage paint. I will see if it has enough bite to do it all in one shot, but for this project I don't mind spending the extra time chasing a little more perfection in the cutting phase because it is for a good friend of mine.

This is the first classic car I'm getting to put this type of work in to, and I'm hoping that it will open the door for me to do more of these types of vehicles. In this instance I'm definitely going to be putting in more work than I'm being paid for, but I'm just going to love every second of it. There is something different about working on a car that is a passion project for someone, as opposed to a modern daily or something similar. Although, I do love modern vehicles as well. I work as an engineer at an aftermarket air filter company and I get to see all kinds of these vehicles every day. Admittedly it does desensitize me a bit though. I see a new BMW and a kinda just roll my eyes, but someone brings in a pristine C6 Corvette and I'm drooling.







I would take John aka 2black1s advice for the chipping and peeling paint. With cars like this - it simply is what it is. Do your best, educate your customer and move on.

https://www.autogeekonline.net/forum/attachments/ask-mike-phillips-your-detailing-questions-/72717d1615405520-im-polishing-63-continental-weekend-could-use-some-tips-first-post-20210308_182155-jpg





https://www.autogeekonline.net/forum/attachments/ask-mike-phillips-your-detailing-questions-/72718d1615406058-im-polishing-63-continental-weekend-could-use-some-tips-first-post-20210308_181138-2-jpg

If it were me? I'd carefully machine buff all around it and then lightly buff over it and call it good. Don't turn a mole hill into a mountain.

http://www.autogeekonline.net/gallery/data/715/Molehill_into_Mountain.jpg



I can absolutely appreciate the "mountains and molehills" analogy, and I am sometimes guilty of sweating the small parts of a project like this way too much. "Do your best, educate your customer and move on" speaks volumes to me, and it is something that I will keep in mind.






My how-to articles for #7 are mostly for original and antique single stage paints. The paint on a car from 1990 would qualify as antique by most car guys standards, which is usually 20 or 25 years old.


From the look of the results on the trunk lid, if it were me and time was limited, I would test out the 3D Speed with a foam cutting pad. See what you get. A foam cutting pad can leave marring in and of itself so if you use a foam cutting pad, inspect for marring. You could always cut with fiber and re-polish with foam using the 3D Speed instead of a dedicated compound. The cool benefit to 3D Speed is great performance and easy wipe-off.


Just do some testing...


:)


This is what I will do! Thank you again, Mike, for the thorough response and evaluation of my situation.

[crg001]

One more...


I don't recommend this technique for everyone, but it does work.


The COMET Technique by Mike Phillips - 1965 Cadillac - Original Single Stage Paint - Slam job by Mike Phillips (https://www.autogeekonline.net/forum/ask-mike-phillips-your-detailing-questions-/120124-comet-technique-mike-phillips-1965-cadillac-original-single-stage-paint-slam-job-mike-phillips.html)


The COMET Technique for oxidized single stage paint

http://www.autogeekonline.net/gallery/data/3726/1965_Caddy_018.JPG

NOTE: The COMET technique is ONLY for oxidized SINGLE STAGE paint.

Do no try this on a modern clearcoat paint you will likely scour the finish.


Be sure to read the entire article and towards the end, as in my norm - I took a picture and shared what I used to buff out the car including HOW MANY PADS WERE USED.

Most people don't use enough pads when using foam pads to do correction work or when using an AIO


http://www.autogeekonline.net/gallery/data/3726/SlamJob_001.JPG



:buffing:

The first time I saw you mention washing a car with Comet, I thought it was a joke. I thought there was no way that would be good for a car! But after reading it makes a whole lot of sense. That being said, the car's paint isn't horribly oxidized, nor is it all that dirty, so I'll just be doing a waterless wash and clay bar process before going into the polishing phase.

Polishing pads are one thing that I know I don't have enough of. And it seems no matter how many I buy, it still isn't enough. It's tough for someone starting out to have enough, but I try to buy at least 5 or 6 of each new type at a time when I do. They get expensive really, really quick! Hopefully with time I will build up a stock that will give me multiple options for every paint type. I think I'm going to go back to simple flat foam pads, because as much as I love the Uro-Tec's on the G9, it's hard to say how much better they are for the money.

[2black1s]

Thank you so much for the response! This is some very good insight on how this car was resprayed and what caused the peeling edges of the paint. I was afraid to touch those areas, but I will absolutely try chipping away the peeling edges with a razor blade. I think I may leave the blob on the hood alone though, I like Mike's analogy of mountains and molehills for that particular imperfection. Thanks again for your help. I have been following your threads about your deliberation between a Flex and a Mille, and I like your reasonings for choosing the Rupes. I also very much appreciated the tear down photos!

Cheers!

Thanks for your reply.

Regarding the blob on the hood. While I agree 100% with Mike's "Mountain/Molehill" analogy, in fact if you've ever seen any of my posts on touch-up's one thing I always stress is that the repair area should be no larger than the original defect, there is a way for you to address that blob if you so desire.

Here's how I would go about it...

Get a piece of 2" masking tape and cut a hole in the center of it slightly larger than the diameter of the blob. Firmly attach the tape around the blob. Take your razor blade (brand new and sharp) and lay it flat across the tape. Then with a slicing motion remove the blob. Now you will be able to determine what is below the surface.

If it is paint, you're nearly done. You can stop here or you can remove the tape and try to level it a little better. If you stop, now you'll have a blemish that is only about the thickness of the tape (approx .004 - .005") higher than the surrounding finish. Not perfect, but certainly better than what you have now. If you decide to level it further, it now becomes tricky and I'd think very carefully before proceeding.

If it's corrosion or any other foreign substance then you'll need a different approach. In that case I would use the corner of the razor edge to scrape and remove the foreign substance, being careful to remove only what's necessary without enlarging the defect size. Then do a brush touch-up.

In either of these cases you can minimize the appearance of the blob without creating a "mountain out of a molehill".

[Mike Phillips]

3D speed is indeed an amazing product, I was on the fence whether I was going to do a dedicated two-step polishing process and then top with a carnauba wax like Collinite 845, but I decided to Speed things up a bit (lol) by combining the wax and finishing polish step into one, as I feel the Montan wax base will also look incredible on the single stage paint.

I will see if it has enough bite to do it all in one shot, but for this project I don't mind spending the extra time chasing a little more perfection in the cutting phase because it is for a good friend of mine.



For the portion I made red/bold text

From experience, you will get a LOT more shine if you cut the paint first with a fiber pad. If you really want to go nuts - get a rotary polisher and a twisted wool pad and do the initial cut with wool and compound. Old school single stage paint really like wool pads on rotary for removing the oxidation but for also restore a stable HARD shine.






This is the first classic car I'm getting to put this type of work in to, and I'm hoping that it will open the door for me to do more of these types of vehicles.

In this instance I'm definitely going to be putting in more work than I'm being paid for, but I'm just going to love every second of it.



Ditto. I'm guilty of the above from the time I started to today. Forget what everyone says - do what makes you sleep good at night.

An honest man's pillow is his peace of mine - John Cougar Melloncamp - Moments to Memories - Scarecrow Album







There is something different about working on a car that is a passion project for someone, as opposed to a modern daily or something similar. Although, I do love modern vehicles as well. I work as an engineer at an aftermarket air filter company and I get to see all kinds of these vehicles every day. Admittedly it does desensitize me a bit though. I see a new BMW and a kinda just roll my eyes, but someone brings in a pristine C6 Corvette and I'm drooling.



That describes me. I can APPRECIATE modern cars and modern technology but I would rather work on old school Detroit Iron any day of the week. Plus - no stupid plastic trim to tape-off or deal with. :dunno:






The first time I saw you mention washing a car with Comet, I thought it was a joke. I thought there was no way that would be good for a car! But after reading it makes a whole lot of sense. That being said, the car's paint isn't horribly oxidized, nor is it all that dirty, so I'll just be doing a waterless wash and clay bar process before going into the polishing phase.



Save the Comet Technique for another day.

Also - your clay bar is going to get loaded with dead paint, so it will probably only be good for this one project. Nature of the beast.







Polishing pads are one thing that I know I don't have enough of. And it seems no matter how many I buy, it still isn't enough. It's tough for someone starting out to have enough, but I try to buy at least 5 or 6 of each new type at a time when I do. They get expensive really, really quick! Hopefully with time I will build up a stock that will give me multiple options for every paint type. I think I'm going to go back to simple flat foam pads, because as much as I love the Uro-Tec's on the G9, it's hard to say how much better they are for the money.



The simple Lake Country foam flat pads are a time-proven pad. I also like the new RUPES CP foam pads but my guess is they are a few dollars more.


Looking forward to the after pictures.


:)

[Mike Phillips]

More...


One thing most detailers don't do is take time to get great before pictures. The money shot is always the hood.

Check out this article,


The power in the after shots is created in the before shots (http://www.autogeekonline.net/forum/tricks-tips-techniques/21216-power-after-shots-created-before-shots.html)


In the picture below, if you DIDN'T know how bad the paint was BEFORE the paint correction, you wouldn't have as much appreciation for the AFTER results.

http://www.autogeekonline.net/gallery/data/715/beforeaftershot.JPG



And if it helps, take the time and put in the effort to get OVER the hood. Like this,


http://www.autogeekonline.net/gallery/data/3436/1959_Chevy_004.JPG





Here's how I was able to get the high overhead hood shot - I used a ladder.

http://www.autogeekonline.net/gallery/data/3436/1959_Chevy_006.JPG





Once you start working on the hood or the car, it's too late to get the best before shots.


:)