Thanks: 0
Likes: 0
Dislikes: 0
-
Re: Rookie mistake, need help
Originally Posted by Eldorado2k
While I'm hesitant to say you went through the clear, that comment about using a Magic Eraser on paint couldn't be farther from the truth.. I once tried using a Magic Eraser as a last resort in order to remove some extremely stubborn tree sap and ended up with a small dull spot on the paint. [went through the clearcoat] It's a good thing I only did a small test spot.. It's also a good thing it wasn't a showcar or anything crazy like that. I'll never use a Magic Eraser on paint again.
Yeah, that is where I get confused. I'm a novice, no doubt. At the same time, I've watched a ton of videos and read articles about scratch repair before attempting. A pretty reputable auto detailing guy on youtube uses the magic eraser all the time, especially on transfer. It always looks dull afterwards, just like many other videos I've seen but that never scares them. They say its normal for it to be dull and turn on their polisher and use a couple steps, and voila, its back to a beautiful shine. Seeing those black spots appear freaked me out. I wasn't prepared for that.
-
Re: Rookie mistake, need help
No offense taken. This was my first time! I guess I just thought I was better prepared because of all the research I did beforehand. Ever see that video of a guy writing scratch into his car and then promptly gets rid of it?? These videos gave me lots of confidence. And yes, I looked at more reputable videos as well. The spot is only about the size of a quarter and its a 4Runner so I won't be repainting the fender. I just need to cover up my mistake as much as possible. I'm looking to buy a Griots Orbital polisher or a PC. If you look closely at the picture, you will see a dull spot surrounding the black spot. I think that can be fixed with a less abrasive polish and pad. The thing is about getting a DA is that this spot would be hard to get at with a DA. Its a fender that sits out from car a bit. I could tape off lines to make sure I don't get burn I suppose. Thanks for your comments.
-
Re: Rookie mistake, need help
Sorry for so many messages, but how would I know for sure if I went through clear coat? I think in this case, its pretty obvious but are there any tricks? Also, do you think I can apply a spray clear on it successfully? Can I get it to a 8/10? Thanks again, you guys rule!
-
Re: Rookie mistake, need help
You could try doing a spray can clear touchup on it...it likely would look the same after, I don't know. 1K clear touchup will yellow over time though.
I understand your frustration with watching a lot of successful videos, and then having it go down the dumper IRL, but it's just one of those things that is hard to convey--how long to rub, how much pressure...and more importantly, how thin the clear actually is.
-
Re: Rookie mistake, need help
okay, so should my steps be: spray a primer, paint, spray clear, and then eventually polish it lightly? Setec, thanks. I'm from NJ as well but live in Denver area now. My wife trusted me to fix scratches and am feeling a little pressure to recoup her confidence!!
-
Re: Rookie mistake, need help
Originally Posted by Weaverpsu
okay, so should my steps be: spray a primer, paint, spray clear, and then eventually polish it lightly? Setec, thanks. I'm from NJ as well but live in Denver area now. My wife trusted me to fix scratches and am feeling a little pressure to recoup her confidence!!
Just take it to a professional. I won't risk again doing a DIY solution this time. If you want to get experience on that, buy a hood in a scrap yard.
-
Re: Rookie mistake, need help
Originally Posted by hdez
Just take it to a professional. I won't risk again doing a DIY solution this time. If you want to get experience on that, buy a hood in a scrap yard.
ahhh, Booooo. That's no fun lol. How much would they charge?
-
Super Member
Re: Rookie mistake, need help
-
Re: Rookie mistake, need help
so, if I didn't strike through clearcoat, how would I know and what would my course of action be? I bought the chemical guys sampler kit because lots of my scratches are small/thin and won't need the V32 and would use a V34 or 36. Plus the 38 is a finishing polish. I almost bought Meguiars 205 and 105 instead. I have the day off, so that is why I'd like to get as much info as I can today. And I'd love to fix it myself because I'm a frugal son of a gun! And yes, thats the guy! Darren's videos are long but very informative. He uses eraser to rid of transfer. BTW, my first attempt was on our Jetta. Wife hit garage and everything worked out great. I'd say its a 8/10 and won't have any issues with returning lease now. Then I moved on to our new 4Runner Limited, which I love and that is what happened.
-
Super Member
Re: Rookie mistake, need help
Use the V38 with a foam applicator or a foam finishing or polishing pad. Smooth strokes, not too much pressure, but not too little either.
Similar Threads
-
By Hammer77 in forum Auto Detailing 101
Replies: 2
Last Post: 10-17-2016, 08:24 AM
-
By Chase361 in forum Auto Detailing 101
Replies: 10
Last Post: 07-09-2015, 12:00 AM
-
By 11Silverado in forum Auto Detailing 101
Replies: 4
Last Post: 03-09-2015, 05:46 PM
-
By pdhenderson in forum Auto Detailing 101
Replies: 23
Last Post: 11-28-2012, 11:59 AM
-
By Alpenglow OSD in forum Show N' Shine
Replies: 9
Last Post: 03-12-2008, 02:34 AM
Members who have read this thread: 0
There are no members to list at the moment.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
S |
M |
T |
W |
T |
F |
S |
28 | 29 | 30 |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
31
| 1 |
|
Bookmarks