2013 Dodge Charger SRT8 (Dual-stage paint correction w/ CQuartz Finest)

[KMG]

The owner of this car contacted me through my website. He purchased the car earlier this year and ran it through an automatic car wash most of the summer, which just hammered the exterior of the car. After inspecting the car, he decided he would like to have CQuartz Finest installed on the car after it was corrected. The car has roughly 17k miles on it. Onto the good stuff, the pictures.


Picture of the car just after being dropped off


The deck lid, like most of the car was covered in swirl marks


Image showing the condition of the rear bumper which had numerous scratches on the rear bumper cover


This vehicle saw regular use of an automatic car wash over the summer resulting in this


The car was covered in swirls and fine scratches

The Washing Process

First step in my process was to remove the wheels to begin the cleaning process


Omni-clean was used to clean the wheels


Megs Super Degreaser was to clean the barrels of the wheels


The wheel wells were cleaned with various brushes and Megs APC


I proceeded to do a foam pre-soak using Chemical Guys Citrus Wash & Clear w/ Megs Super Degreaser

After this the car was washing using the 2BM, followed by a decon using IronX. I then proceed to was the car again using a Nanoskin fine wash mit. The car was then dried using a few waffle weave towels.


After being fully washed and dried these pictures show the true condition of the paint


The paint was seriously flawed due to use of the automatic car wash


Lots of swirls and scratches



Wheel Coating

The wheels were coated using CQuartz DLUX


The brembo calipers were also coated with DLUX


Paint Correction Process

This was the first test spot I performed using an orange cutting pad w/ FG400 on my rupes 15


Another shot of the same test spot


I did another test spot using the same combo, however this time I was not happy with the results as the surface still had a fair amount of RIDS


I moved on to using Amerirocks on a Megs MF cutting pad on my rupes 15. This produced more of the results I was looking for. It removed a majority of the RIDS


Another 50/50 shot of the same test spot


50/50 shot of the passenger side rocker using Amerirocks on my Rupes Mini


Image of the driver side fender after being compounded with Amerirocks and polished with Reflect


CQuartz Finest Application

The car was then rewashed, and wiped down with Eraser to prep for the the application of CQuartz Finest. This is a picture showing Finest flashing on the paint during application


Quick picture after finishing up the application of Finest


This picture shows the amazing reflective qualities of CQuartz Finest. The gloss on the paint is a mile deep.


Finished Product Shots

Some after shots in the sun today before being picked up























Thanks for looking!

[RottenII]

Car looks amazing! Pulling the wheels is a pain but there is no better way to get them clean.

[Eric@CherryOnTop]

Drool, great job. What was your process for polishing underneath the spoiler?


Sent from my iPad using Tapatalk

[KMG]

Drool, great job. What was your process for polishing underneath the spoiler?


Sent from my iPad using Tapatalk

As you can see in the last picture, the Super Bee stripe on the back of the car is a vinyl graphic and runs under the spoiler so that area did not require any paint correction. I just thoroughly cleaned this area, however it was coated with Finest.

[FrankS]

Nice job!

[Corey@OptimalDetailing]

Great job! That black looks simply amazing now. Great 50/50 shots.

[281]

Awesome work! Can't believe the condition of the car and it's only a 13'

[Marc08EX]

Amazing job! The 50/50 shots are right on the money.

[richy]

Great save!!


Sent from my iPhone 5 using Tapatalk

[Meticulous-Detail]

Awesome job! Love the 50/50 and love that Charger SB too