Try 3D Towel Kleen very economical. I use that and CG MF detergent. Those are the two I found that do the best job for the money. It's even better when you find out they are telling you to use way...
I finally got to testing it on my wife's 06 Honda Odyssey. Her paint is never trashed so I needed a good cutting AIO to pull up the gloss and lay down some protection. I used B&S orange foam and B&S...
Hey Tom,
There are tons of options out there that could get you close. Your looking for my favorite type of products. Not a coating but close to it in longevity. There are several hybrid products...
They majority of towels I own are Rag Co. I get what I need at a very fair price. I have never had issues with lint or shedding except for the first wash and dry. Chances are many negative comments...
Meg's Hyperwash
Daytona Speedmaster Pro wheel brush- 8 years and still going
IUDJ- Never ceases to impress me. It's my most reached for product.
Meguiar's DUB, Ultimate wheel cleaner. They don't...
Finish Kare Hi-Temp, Collinite 476 are going to give you the most durability on a paste wax. If you go thin you will have no problems getting them off. I would go for 476 I'm just a Collinite fan....
I'm sure some of these have been mentioned. Collinite 476, 845, Polish Angel Master Sealant, Soft 99 Fusso Coat (Epic water behavior, durability and starting to get cheaper in the states) Prima Epic...
+1 Ronin. I came to the conclusion that in reality coatings are superb for the things that have always been a detailing nightmare, Trim, Rims ( Engine Bays if you a handy enough to take parts out to...
They are no more scratch resistant then your "scratch resistant" clear coats if anything less. You can still scratch them and induce marring with poor washing habits just like any other clear coat....
Menz tend to be on the oily side especially when you get down to the finer polishes. Your using 2500 on Honda paint try a firmer pad with less product. Prime your pad with 5 pea size drops of product...
It comes down to what you want. You will make trade offs. Rule of thumb the better the glossier they look "show wax blends" higher oil content more gloss yields less durability. ( Rule of thumb but...
It's entirely about what set of circumstances you want to put up with. They have positives and negatives. I only coat trim and rims. Nothing can protect and make rims easier to clean then coating it....
I can assure you that there are things in this world and life that Hawkins had a hard time wrapping his mind around. He was a brilliant mind and I wish I could have sat down with him to just discuss...
Machine does not matter it's skill and materials. If you know your tools and have the technique you should be able to do whatever you want with the paint. Just because it's a smaller hammer does not...
Have a bucket of APC and hot water ready. Toss them in as your working when they are spent. Go right from the bucket to hot water wash. You may need to wash them a few times with hot water and a...
D300 was on my list along with Cut & Finish. I'm going to seal it with Prima Epic. I thank you for your help I know Cut & Finish should knock them out.
Hey Guys,
Looking to do a two on a 2016 Mazda 3 Deep Blue Mica daily driver. It has complimentary dealer installed holograms. I have a few RIDS to spot compound out, the rest is all spider webs and...
Prima Amigo. Easy to use on any paint. Think about it as cleansing polish with really good filling abilities. It will marry with 845 without any durability issues at all. It will darken your paint...
If your having problems with the starting to delaminate you are running them too hot. I've had mine for a while and probably have put 4 sessions on each and no problems. I just swap out every panel,...
Microfiber has a high melting of 245 degrees so I don't think anyone runs a hot water heater that high.. I run mine at 117 degrees. My HE washer will also heat water to make it hotter based on the...
