Turtle Wax Seal and Shine

[Coatingsarecrack]

^^You tried buffing off immediately after spreading or did you wait extended time to buff off (was SWETM’s question)?

I applied and wiped off right away per instruction.


Sent from my iPhone using Tapatalk

[Don M]

An update on the companion product to Seal N Shine, the ICE Spray Detailer......

I had a small bird bomb on my quarter panel when I got off work. It was in the direct sunlight, 85+ and high humidity, I misted it on the bomb and the surrounding area and wiped it off. Not a streak or smear anywhere. I was impressed.

[rlmccarty2000]

Since the mods are allowing this discussion to continue I’ll chime in with my directions for my best results. Spray lightly on a microfiber applicator, spread normally, wipe thoroughly, wash with McKees 914. The wash step is important to bring out the majority of the gloss. I scrubbed the heck out of it, but a simple wash is the easiest way.

I’m going to get some TW Quick Detailer and see if that will substitute for the wash step.

[Klasse Act]

Since the mods are allowing this discussion to continue I’ll chime in with my directions for my best results. Spray lightly on a microfiber applicator, spread normally, wipe thoroughly, wash with McKees 914. The wash step is important to bring out the majority of the gloss. I scrubbed the heck out of it, but a simple wash is the easiest way.

I’m going to get some TW Quick Detailer and see if that will substitute for the wash step.

When applying this to a clean surface, as most everyone does, what's the point of hitting it with N914 when you done applying it?

[FUNX650]

Not issues.... issue

I applied to applicator wiped on wiped off.....
unless it is different than the vast majority
of sealants out their....

Maybe 4 sprays to much but I have not
had problems removing ANY other product
I applied.

•IMO:
-Yes it was ”issues”.

This time around you not only conveniently
left out this set of original “issues”:
“Did second coat 1.45 hours later
and found 1st coat hadn’t dried.
Buffed off but still streaking”.

But you added this “new issue”:

Feels “greasy”

As such:
I’m still going to go with my
previous posting; that being:

Just curious:
All these “issues”—yet adhering
to the product’s instructions?

Bob

[Klasse Act]

How about temp and more importantly HUMIDITY

Sent from my SM-G950U using Tapatalk

[FUNX650]

How about temp and
more importantly HUMIDITY

^^Good points.

•And don’t forget about the immediate
work area’s air-speed, as well.






Bob

[Coatingsarecrack]

How about temp and more importantly HUMIDITY

Sent from my SM-G950U using Tapatalk

It was lightly raining but car in garage. Garage door open


Sent from my iPhone using Tapatalk

[Coatingsarecrack]

•IMO:
-Yes it was ”issues”.

This time around you not only conveniently
left out this set of original “issues”:
“Did second coat 1.45 hours later
and found 1st coat hadn’t dried.
Buffed off but still streaking”.

But you added this “new issue”:


As such:
I’m still going to go with my
previous posting; that being:



Bob

Nope one issue 1st coat hard to remove, second coat was hard to remove. Was hard to remove. If I said something like left high spots.... then issues....

It feeling greasy was just observation not an issue


Sent from my iPhone using Tapatalk

[Coatingsarecrack]

Maybe I got a bunk bottle? Can someone post a pic of little of it. I will do same once I’m home. I’ve been thinking that maybe because it has wax needs more buffing?

Haven’t used anything with wax in it for 15 years.


Sent from my iPhone using Tapatalk