-
Pressure washer kinkless hose
Looking to replace my hose on my ryobi to a kinkless (rubber?) hose. It’s 2300 psi and 1.2gpm’s. Their was a thread here or on autopilot with good info in it but I can’t remember or find it. I’m looking for the proper diameter of hose 1/4, 3/8 or whatever fits. Recommendations on brands would be nice too.
Thanks in advanced
Sent from my iPhone using Tapatalk
-
Re: Pressure washer kinkless hose
Have you looked into Flexzilla? No experience with their pressure washer hose, but I have their garden hose and I’m satisfied with it.
-
Re: Pressure washer kinkless hose
MTM ones from Obsessed Garage or MTM directly.
-
Re: Pressure washer kinkless hose
I replaced my Ryobi with a Flexzilla.
You just have to straighten it out before using to unwind the circle.
It lays fairly flat and never kinks.
I suppose if you left a loop in it and pulled hard it would pinch.
A much better hose than the stock pvc(or whatever material)
-
Re: Pressure washer kinkless hose
Funny you post this I just replaced a hose myself. I was about to kill the poor little Ryobi over the garbage stock hose. Grabbed a 30' 1/4" Simpson. Felt good out of the box I will let you know how it works.
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
zero4
MTM ones from Obsessed Garage or MTM directly.
The mtm was what I was gonna buy but in other thread I mentioned some guy had issue as I believe Kobrajet is 3/8 hose and ryobi uses 1/4. On site obsessed garage guy says that hose runs no problem on ryobi but he’s not personally using a ryobi (I wouldn’t either with a kranzle but won’t spend that money to spray water). Other guy ryobi was his “daily driver”.
Sent from my iPhone using Tapatalk
-
Re: Pressure washer kinkless hose
I'm using a 1/4" single wire PW hose on my SPX3000 from Kleen-rite. Super high quality (made by Continental) and is in near mint condition after two seasons of use. Only cost $60 + some 3/8" MTM adapters.
50' Black 1/4" Single Wirebraid Hose with 3/8" Ends - Kleen-Rite Corporation
-
Re: Pressure washer kinkless hose
I’m looking for the same type of hose to replace the one on my AR Blue power washer. Anyone replaced one? Why are plastic hoses a thing anyway?
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
DetailZeus
Funny you post this I just replaced a hose myself. I was about to kill the poor little Ryobi over the garbage stock hose. Grabbed a 30' 1/4" Simpson. Felt good out of the box I will let you know how it works.
I have the 30' Simpson as an extension to my 25' hose on my Simoniz pressure washer. It's an upgrade from the super cheap hoses that come with basic pressure washers but it's not perfect. I will not kink, but it do tend to coil up a little bit, it's much worse when it's cold outside too.
If you want top of the line hoses, you might want to check Obsessed garage and see what Matt proposes. He tests everything. Only downside is that his recommendations are often very expensive. On a hose I think it would be a good investment since it's something that lasts a long time and can cause quite a bit of annoyance when you use a poor product. You will need to buy adaptors if you want to replace the basic hoses with high quality ones. You should watch the Ryobi testing videos Matt did on his youtube channel.
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
rlmccarty2000
I’m looking for the same type of hose to replace the one on my AR Blue power washer. Anyone replaced one? Why are plastic hoses a thing anyway?
Cost? Why else do companies sell crappy stuff? Cheap plastic hoses do the job, it's just annoying to use them.
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
Calendyr
I have the 30' Simpson as an extension to my 25' hose on my Simoniz pressure washer. It's an upgrade from the super cheap hoses that come with basic pressure washers but it's not perfect. I will not kink, but it do tend to coil up a little bit, it's much worse when it's cold outside too.
If you want top of the line hoses, you might want to check Obsessed garage and see what Matt proposes. He tests everything. Only downside is that his recommendations are often very expensive. On a hose I think it would be a good investment since it's something that lasts a long time and can cause quite a bit of annoyance when you use a poor product. You will need to buy adaptors if you want to replace the basic hoses with high quality ones. You should watch the Ryobi testing videos Matt did on his youtube channel.
Yeah he recommends mtm kobrajet which I don’t mind spending the money but I. An only find 3/8 inch. He says will work fine on ryobi but as he uses a kranzel I don’t know amount of testing he’s done. Thinking of it like car exhaust as wider diameter with out adding hp or forced induction will loose out on torque. Wanting to stay with 1/4 in hose.
Sent from my iPhone using Tapatalk
-
Re: Pressure washer kinkless hose
I use the Cobra 3/8" on my Sunjoe 3000 - which is only ~1800 PSI - ZERO Issues - actually helps with flow.
MTM Cobra Hose
I actually replaced everything from the hose connection out with MTM Parts - much better than any manufacturer parts... MTM makes full kits now if you want an easy option of parts that will mate together.
Any questions just call them - they have excellent customer service and will not steer you wrong for any and all PW needs.
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
Coatingsarecrack
Yeah he recommends mtm kobrajet which I don’t mind spending the money but I. An only find 3/8 inch. He says will work fine on ryobi but as he uses a kranzel I don’t know amount of testing he’s done. Thinking of it like car exhaust as wider diameter with out adding hp or forced induction will loose out on torque. Wanting to stay with 1/4 in hose.
Sent from my iPhone using Tapatalk
yes the products matt uses are top of the line and expensive but you get what you pay for and he believes it makes for a better experience and i believe it. watch his videos on the cheap pressure washers. he uses the kobrajet hose and pressure is basically the same even though its a 3/8 hose. and look at how the hose lays down in the videos. doesnt look like it really kinks up and lays down quite nicely.
-
Re: Pressure washer kinkless hose
I've got 2 25' Flexzilla hoses on my 2000PSI Ryobi (a 1/4 and a 3/8). Both are a huge upgrade. The 3/8 loses a little pressure but flows more water so I like it better for washing cars with.
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
talonted
I've got 2 25' Flexzilla hoses on my 2000PSI Ryobi (a 1/4 and a 3/8). Both are a huge upgrade. The 3/8 loses a little pressure but flows more water so I like it better for washing cars with.
Is this really what happens? I always assumed the washer would just build pressure until it reached where it needs to be, like when you first turn it on.
-
Re: Pressure washer kinkless hose
Agreed on Obsessed Garage- most everything he likes, and obviously sells is overpriced (if your looking for entry level gear-not him) He even comes down hard on anyone that chooses to use Big Box Store Pressure Washers too. Sure ya get what you spend on, but not everyone has a GT3 they can test out hundreds of products on! He knows his stuff, but likes to tell you that over and over in his very lengthy videos! One can only take so much of him going off course. lol. Anyway- sure wish there was some type of "Compatibility Chart" for what hoses and attachments are universal with different Pressure Washers!
-
Re: Pressure washer kinkless hose
Here's another avenue for you guys. This Co answered my email in less than an hour w great advice and linked products for my 2000Psi Greenworks Unit. After 1-2 email with Matt at OG, I wouldn't give him the satisfaction of buying a friggin hat from him! This Co looks like they carry anything you need to augment whatever PW you own now! Ask for ZACH for sure!
https://www.esotericcarcare.com/pres...-foam-cannons/
-
Re: Pressure washer kinkless hose
Gunny - Thanks for the info! I had looked at a lot of the MTM stuff at their site directly - looks like they've got lower prices than going direct.
-
Re: Pressure washer kinkless hose
Not one to go around different threads slamming people, but I'd rather throw my cash out the moonroof of my RCF than give MM from OG anything. His condescending replies are ridiculous. If you dont offer a Military Discount just say "Sorry, I dont have those" instead of " I've worked too long and hard to give anything I own away " and even more I wont get into. Guy just rubs me wrong in everything he does! Videos may educate you here n there but get to the dmn point ya know! Definitely looking for better gear to augment my "cheap and useless" (according to him) Greenworks PW, and it will NOT be from him - even if he was giving it away (which we know ain't happening!) Lol. Hell, a friend dropped 1k w him on stuff n the Tool wouldnt drop a Tshirt in box w all the new gear!
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
Gunny Fitz
Not one to go around different threads slamming people, but I'd rather throw my cash out the moonroof of my RCF than give MM from OG anything. His condescending replies are ridiculous. If you dont offer a Military Discount just say "Sorry, I dont have those" instead of " I've worked too long and hard to give anything I own away " and even more I wont get into. Guy just rubs me wrong in everything he does! Videos may educate you here n there but get to the dmn point ya know! Definitely looking for better gear to augment my "cheap and useless" (according to him) Greenworks PW, and it will NOT be from him - even if he was giving it away (which we know ain't happening!) Lol. Hell, a friend dropped 1k w him on stuff n the Tool wouldnt drop a Tshirt in box w all the new gear!
While I agree that some people can rub me the wrong way too. I generally don't factor that in when I decide where to buy. For me it's all about having the best deal and best service. I have blacklisted only one vendor since I started my business for making a very rude and insulting comment to me directly. Otherwise, even if I don't like the guy presenting the tool or product, if he offers the best price and good service or best service and decent price, I would not avoid purchasing from him.
In the case of Matt, I think he is a bit snob about the way he approaches tools and products... it's either good or complete crap for him. Where in reality even the worst products and tools will still get the job done. I think he will appeal to people who only want to buy the best possible at any price. Me I am all about price/result ratio for most of what i buy. So it's unlikelly I would buy from him either because he will never be offering what I am looking for unless the very best is at a reasonable price, and it's rare that it is.
-
Re: Pressure washer kinkless hose
I think it's interesting the way Matt comes off to different people. My first experience with his channel was watching him use the sunjoe spx3001 (probably his most disliked video??) for the first time. I'll admit I was like this dude is so ridiculous, but I just kept on watching. Eventually I later subscribed, and as I started to watch a bit more of his content, and hear his thoughts on what he's doing and how he thinks - I realizes he's just like any of us. If money wasn't a factor, we'd likely buy the best we could for something we enjoy doing. It's the obsessiveness and attention to detail that's allowed his website to really grow into somethin impressive (imo, anyway.) If you consider something from his perspective, it usually makes sense.
He sells Kranzle because they hardly ever have issues, which makes perfect sense. I like to invest in things, especially things I think I'll have for a long time. So while the 1122TS package might be expensive, if you have it for ten years (which is probably not unreasonable to assume) then the price sort of becomes irrelevant. $1600 over 10 years is just 160 bucks a year, and that's assuming the worst and the machine explodes right at the 10 year mark. Maybe you'll have it for 20 years, who knows? It isn't for everyone, and he's pretty clear that he doesn't want to appeal to everyone. He wants to appeal to the person who can look past the sticker shock and see the long term value.
The same argument could be made for dress shoes. My step dad used to berate me for wanting to buy a pair of Allen Edmonds shoes. He told me cheaper ones are more than good enough. Sure, but can you resole a pair of dress shoes from JC Penny? I would much rather invest in a pair of shoes I can have for the rest of my life. Same mentality, just different areas of life.
I personally find it interesting that some people are put off by the sticker price of his 1122TS package, but are willing to buy multiple units in the $150-250 price range just to have back ups in case one fails. I feel like that itself speaks to the quality of these big box machines, and explains pretty easily why he calls them junk (which seems to irritate people.) I fully expect my greenworks unit I bought as a package from him with all the fixins to fail sooner rather than later. Maybe it won't, but that would be anecdotal evidence at best that the brand is super durable high quality stuff. I hope that when it finally dies (and I figure out whether or not I want to pursue a nicer unit) I'm in a position to buy a 1322TS from his store.
He's pretty overbearing, sure. Could definitely tone down how dramatic he is, but at the end of the day he is who he is. That's probably why he has such a strong following. Too many youtubers are overly positive about everything and never just tell it like it is. He does. If he thinks something is junk - he'll say it. He's not attacking you for liking the product, you aren't what you buy. He just doesn't like it.
All of that being said, I'm not 100% with him about plenty of things. I think his obsession with Rupes is a little much, his hesitation towards rinseless washing seems silly to me, I find it amusing he's worried about scratching his ratchets, but it's just part of the deal with watching his stuff. In return for putting up with his quirks (everyone has their own quirks), he does things like buy 50 pressure washers and test flow, pressure, and set up a sick page on his website so you can easily outfit yours with higher quality accessories. He vlogs training from Optimum and Esoteric, and has Andy Ward and Jason Kilmer make appearances and walk you through their processes. He puts out some seriously good content. Some videos may be long - but if that's not your thing you're definitely watching the wrong channel, lol.
This is the end of my thoughts, so if you stuck with me - kudos to you.
tl:dr I think Matt gets a lot of harsh snap judgments, and that he's not nearly as bad as people make him out to be in their heads.
-
Re: Pressure washer kinkless hose
@Finick. If that post would’ve been any longer, you would’ve had to split it up into chapters.[emoji23]
I think you’re becoming a little “Obsessed” with detailing.[emoji57]lol. J/k
-
Re: Pressure washer kinkless hose
lmao, i didn't even realize how long it had gotten until I was done.
I guess it's not even really the detailing that appeals to me, I just really appreciate channels I think put out quality content. In any of the given areas of interest i have, I'll kind of search for channels I feel just really nail their content. Steve Ramsey puts out great woodworking content, Coop from garage gym reviews does a good job being as unbiased as he can, barbell medicine kills it in their seminars on training methodology and pain management, and if you had to ask me about my favorite detailing channel.. It might actually be Loaches channel: Waxmode. His videos are straight to the point and informative. Plus watching him hose his car off is somehow mesmerizing.
-
Pressure washer kinkless hose
That post was as long as 1 of Moremans videos.[emoji23]
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
Finick
I think it's interesting the way Matt comes off to different people. My first experience with his channel was watching him use the sunjoe spx3001 (probably his most disliked video??) for the first time. I'll admit I was like this dude is so ridiculous, but I just kept on watching. Eventually I later subscribed, and as I started to watch a bit more of his content, and hear his thoughts on what he's doing and how he thinks - I realizes he's just like any of us. If money wasn't a factor, we'd likely buy the best we could for something we enjoy doing. It's the obsessiveness and attention to detail that's allowed his website to really grow into somethin impressive (imo, anyway.) If you consider something from his perspective, it usually makes sense.
He sells Kranzle because they hardly ever have issues, which makes perfect sense. I like to invest in things, especially things I think I'll have for a long time. So while the 1122TS package might be expensive, if you have it for ten years (which is probably not unreasonable to assume) then the price sort of becomes irrelevant. $1600 over 10 years is just 160 bucks a year, and that's assuming the worst and the machine explodes right at the 10 year mark. Maybe you'll have it for 20 years, who knows? It isn't for everyone, and he's pretty clear that he doesn't want to appeal to everyone. He wants to appeal to the person who can look past the sticker shock and see the long term value.
The same argument could be made for dress shoes. My step dad used to berate me for wanting to buy a pair of Allen Edmonds shoes. He told me cheaper ones are more than good enough. Sure, but can you resole a pair of dress shoes from JC Penny? I would much rather invest in a pair of shoes I can have for the rest of my life. Same mentality, just different areas of life.
I personally find it interesting that some people are put off by the sticker price of his 1122TS package, but are willing to buy multiple units in the $150-250 price range just to have back ups in case one fails. I feel like that itself speaks to the quality of these big box machines, and explains pretty easily why he calls them junk (which seems to irritate people.) I fully expect my greenworks unit I bought as a package from him with all the fixins to fail sooner rather than later. Maybe it won't, but that would be anecdotal evidence at best that the brand is super durable high quality stuff. I hope that when it finally dies (and I figure out whether or not I want to pursue a nicer unit) I'm in a position to buy a 1322TS from his store.
He's pretty overbearing, sure. Could definitely tone down how dramatic he is, but at the end of the day he is who he is. That's probably why he has such a strong following. Too many youtubers are overly positive about everything and never just tell it like it is. He does. If he thinks something is junk - he'll say it. He's not attacking you for liking the product, you aren't what you buy. He just doesn't like it.
All of that being said, I'm not 100% with him about plenty of things. I think his obsession with Rupes is a little much, his hesitation towards rinseless washing seems silly to me, I find it amusing he's worried about scratching his ratchets, but it's just part of the deal with watching his stuff. In return for putting up with his quirks (everyone has their own quirks), he does things like buy 50 pressure washers and test flow, pressure, and set up a sick page on his website so you can easily outfit yours with higher quality accessories. He vlogs training from Optimum and Esoteric, and has Andy Ward and Jason Kilmer make appearances and walk you through their processes. He puts out some seriously good content. Some videos may be long - but if that's not your thing you're definitely watching the wrong channel, lol.
This is the end of my thoughts, so if you stuck with me - kudos to you.
tl:dr I think Matt gets a lot of harsh snap judgments, and that he's not nearly as bad as people make him out to be in their heads.
I agree with most of what you said, especially about Matt and the quality of his content.
Where I disagree is the quality of regular big store pressure washers. Let me explain...
Take the Kranzle and it's 1600$ price. Sure you may never have any problem with it and it may last you 20 years. And yes assuming you keep it 10 years that is roughly 160$ per year.
Now, compare with what I did and let's see what the numbers look like.
I purchased a Wal-Mart pressure washer in 2013. Their brand here is called Tune-it! but basicly it's a greenworks from what I have seen on Matt's video. It was the entry level 1500 psi model and I paid 40$ for it on sales. I used it for 2 years in my detailing business until the end of 2014. The reason it broke is I forgot to bring it in from my truck when the first freezing nights came and water froze inside the unit and broke something. If it would have been a Kranzle, I am pretty certain the same thing would have happened. So I just put it in the trash and purchased a replacement. If I had a Kranzle, I would have wanted to repair it... what is the cost for that? Probably over 400$. So had I gone the Kranzle road, I would have been 2000$ in after 2 years.
Then I purchased a Simoniz 1700 psi at Canadian Tire, 100$ on special (from 200$). I am still using it. I also purchased an other PW from Canadian Tire that same year, a Sundance 1800 psi unit (same company as Siminoz, can't remember the name but they make all their machines), I paid 100$ for that too. So after 6 years I am 240$ in just for the machines. Last year after reading a post here about better hoses and guns, I purchased an extension hose and a short gun off of Amazon. Hose was 30$ and gun was 20$. So overall, I am 290$ in, and I have a backup unit if anything happens to my main PW. Over 10 years that would be 29$ per year or 14,5% of what Matt proposes. Also, my prices are CAN$ and his are US$... value fluctuate but usually US$ are worth about 20% more... so the difference is even wider because of that.
One of the upsides is that if my machine breaks, I can keep working. Where as if my Kranzle breaked, how long would I be out of a pressure washer while it got repaired? A week or more I would think.
The Kranzle is a better machine puting out more water but I have never felt my machines were not sufficient for doing the job. And watching all of Matt's videos about PW, he never convinced me of any real advantages of having high end machines.
So yes, there are advantages of having top shelf equipment, but I think as a pro, that may not be the best way to go about it.
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
Finick
lmao, i didn't even realize how long it had gotten until I was done.
I guess it's not even really the detailing that appeals to me, I just really appreciate channels I think put out quality content. In any of the given areas of interest i have, I'll kind of search for channels I feel just really nail their content. Steve Ramsey puts out great woodworking content, Coop from garage gym reviews does a good job being as unbiased as he can, barbell medicine kills it in their seminars on training methodology and pain management, and if you had to ask me about my favorite detailing channel.. It might actually be Loaches channel: Waxmode. His videos are straight to the point and informative. Plus watching him hose his car off is somehow mesmerizing.
I like Steve Ramsey too...I stopped watching og after the whole spray bottle obsession...I can't take it
Sent from my LG-Q710AL using Autogeekonline mobile app
-
Re: Pressure washer kinkless hose
Gents- I seriously hope my comments didnt instigate this whole issue on Matt from OG? After all, it's a Hose Thread! Lol.
@Finick - Was going to Reply With Quote on your novel, but that would just take up way too much real estate here. It's so insane that you make mention, and use the "Shoe Analogy" because I've recently started rebuilding my Wardrobe at Mens Warehouse and read hundreds of awesome articles on this site called "Real Men, Real Style" which the owner is a Former Marine too! He put this article out which really does put things into perspective like your analogy! Here it is:
High End Dress Shoes - 10 Buying Mistakes To AVOID
I'd be a hypocrite if I said I didnt enjoy owning the better things in life regardless of cost! (You guys should see my car and what I've done to it!) So yes, I agree w what's said about initial sticker shock!
I guess what bothers me is the way he looks down upon anyone who chooses to go with products NOT endorsed by him. We all know people like this who are not sympathetic enough to understand most of us just cant go out and purchase a Porsche GT3 (and flaunt the whole purchase in a video for all to see) and like I said, I have nothing against those accompanies who do NOT offer a Military Discount because it's their choice - not a right as many junior troops believe. No problem w that, but dont demean me for simply asking! As I've shared w a Member here who sent me a PM, I'm actually very humble and feel odd when kind people thank me for my service. As far as I'm concerned it's those who were killed in action who rate this thanks - but obviously dont bark at anyone for saying it to me. Enough said on that, I moved on just fine and with help from fellow members here have everything ready to order to augment my Big Box, cheap, useless, garbage Greenworks Pressure Washer (lol) and its definitely not from OG.
One thing I didnt think much about was going w a 1/4" hose vs the 3/8" one! Didnt even think it would potentially lower the water output, so thanks to him I'll be going w a 50ft 1/4" one instead! Has anyone here gone w the 3/8" hose on their electric PW and wished they went w 1/4" instead? I havnt pulled the trigger on it all yet and would love to hear all your thoughts on this matter? Oh, another item this Member brought to my attention is the Griots Boss Foam Cannon which appears to produce wicked amounts of foam and has some other features too. However, I did find a YouTube vid where the guy tried this Boss unit out against the new MTM Foamer and the little plastic pieces inside the container actually prevented the Boss unit from producing more foam than MTM. Therefore, I told him I'd let him try out their newer Boss unit before going w that item. I will be getting the complete MTM Pro Kit from Zach @ Esoteric. He sent me a very kind and informative email about this kit. https://www.esotericcarcare.com/mtm-...am-cannon-kit/
I'll stop here before I run this Thread onto Page 20, and once again thank you all for sharing your thoughts and experiences w me/ us all. After all, isnt that what Forums are for guys!
Enjoy Super Bowl Sunday with another Pat's win! (No bandwagon here. Born n raised in New England so always loved them!)
Semper Fidelis.....
Gunny
-
Pressure washer kinkless hose
Quote:
Originally Posted by
Gunny Fitz
Gents- I seriously hope my comments didnt instigate this whole issue on Matt from OG? After all, it's a Hose Thread! Lol.
There’s no issue with him. Besides he’s a big boy, I’m sure he can handle any criticism if and when it happens without getting butthurt.
IMO anyone who puts themselves out there including on this forum should be able to take it just as much as they dish it out without getting mad about simple words. If they can’t then they should’ve remained lurkers. Lol.
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
Eldorado2k
There’s no issue with him. Besides he’s a big boy, I’m sure he can handle any criticism if and when it happens without getting butthurt.
IMO anyone who puts themselves out there including on this forum should be able to take it just as much as they dish it out without getting mad about simple words. If they can’t then they should’ve remained lurkers. Lol.
Eldor do you how hard criticism is to give around here? I'm sure I got a warming or something in my email from autogeek somewhere. I put lotion on before give constructive criticism.
Sent from my SM-N960U using Autogeekonline mobile app
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
Gunny Fitz
I'd be a hypocrite if I said I didnt enjoy owning the better things in life regardless of cost! (You guys should see my car and what I've done to it!) So yes, I agree w what's said about initial sticker shock!
I guess what bothers me is the way he looks down upon anyone who chooses to go with products NOT endorsed by him. We all know people like this who are not sympathetic enough to understand most of us just cant go out and purchase a Porsche GT3 (and flaunt the whole purchase in a video for all to see) and like I said, I have nothing against those accompanies who do NOT offer a Military Discount because it's their choice - not a right as many junior troops believe. No problem w that, but dont demean me for simply asking! As I've shared w a Member here who sent me a PM, I'm actually very humble and feel odd when kind people thank me for my service. As far as I'm concerned it's those who were killed in action who rate this thanks - but obviously dont bark at anyone for saying it to me. Enough said on that, I moved on just fine and with help from fellow members here have everything ready to order to augment my Big Box, cheap, useless, garbage Greenworks Pressure Washer (lol) and its definitely not from OG.
One thing I didnt think much about was going w a 1/4" hose vs the 3/8" one! Didnt even think it would potentially lower the water output, so thanks to him I'll be going w a 50ft 1/4" one instead! Has anyone here gone w the 3/8" hose on their electric PW and wished they went w 1/4" instead? I havnt pulled the trigger on it all yet and would love to hear all your thoughts on this matter? Oh, another item this Member brought to my attention is the Griots Boss Foam Cannon which appears to produce wicked amounts of foam and has some other features too. However, I did find a YouTube vid where the guy tried this Boss unit out against the new MTM Foamer and the little plastic pieces inside the container actually prevented the Boss unit from producing more foam than MTM. Therefore, I told him I'd let him try out their newer Boss unit before going w that item. I will be getting the complete MTM Pro Kit from Zach @ Esoteric. He sent me a very kind and informative email about this kit.
https://www.esotericcarcare.com/mtm-...am-cannon-kit/
I'll stop here before I run this Thread onto Page 20, and once again thank you all for sharing your thoughts and experiences w me/ us all. After all, isnt that what Forums are for guys!
Enjoy Super Bowl Sunday with another Pat's win! (No bandwagon here. Born n raised in New England so always loved them!)
Semper Fidelis.....
Gunny
First off what’s your car and what mods have you done? Share! Second Your time spending defending our country didn’t result in your death doesn’t mean you don’t deserve the respect. Thank you for your service.
You did a job for your country that most wont or can’t do.
I found a 35 foot hose from ryobi that I’m stoked about. Wanted a 50 but I can get around my care with stock 25 footer so this should do I’ll review and post soon. The Griots boss cannon is a system. Their liquids for this system are a lot thinner before diluted. I f using the system go with the boss if not go with the MTM. Don’t cheap out. I bought the sud magic one from online cuz it has good reviews and wish I woulda just spent it on the a better one. If you haven’t checked out the boss soaps do so. The foaming surface wash is the best performing foam soap I have used. Others rave about the polygloss.
Again I feel 1/4 is used for a reason. I feel would be drop in psi and don’t know if it would affect flow rate. Also non of us actually knows how that affects pump? Motor? Most 3/8 I can find are for gas would have to assume because their stronger psi and more flow.
I’m from Seattle I think you know who I don’t want to win today! Hoping for the 1st tie ever....lol
Sent from my iPhone using Tapatalk
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
Eldorado2k
There’s no issue with him. Besides he’s a big boy, I’m sure he can handle any criticism if and when it happens without getting butthurt.
IMO anyone who puts themselves out there including on this forum should be able to take it just as much as they dish it out without getting mad about simple words. If they can’t then they should’ve remained lurkers. Lol.
I don't know about that. A lot of youtubers take any questions or comments as personnal attacks. I know because I often ask questions in hopes of getting more information and I would say that about half the time, the answer when I get one is a defensive post trying to justify their position instead of an answer to my question, and that is when it's not an direct insult or close to it. Many of these guys think what they say is gospel and should not be questioned or asked to provide more information... it's very strange.
-
Re: Pressure washer kinkless hose
I have not tried a 3/8 hose because I had read it was a bad idea to use them on a pressure washer.
What I can tell you is that adding an extension hose on my machine, going from 25 feet to 55 feet (25 feet hose plus a 30 feet extension) makes my machines shut down slower. With just the original hose, the machine stops immediatelly after I release the trigger on the gun. With the extension in place, it takes 1 or 2 seconds before it shuts down.
So I am confident that using a 3/8 would make this even worse. I don't know it would do for the overall flow and pressure, but I doubt it would be good.
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
Calendyr
I don't know about that. A lot of youtubers take any questions or comments as personnal attacks. I know because I often ask questions in hopes of getting more information and I would say that about half the time, the answer when I get one is a defensive post trying to justify their position instead of an answer to my question, and that is when it's not an direct insult or close to it. Many of these guys think what they say is gospel and should not be questioned or asked to provide more information... it's very strange.
I agree 100% with what you said. My post was more of an optimistic look at how it outta be. I’ve dealt with the same exact thing you speak of. It’s like you can’t even ask a simple question without certain youtubers getting immediately defensive + waiting for their flock to jump in. It’s weak!
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
Eldorado2k
I agree 100% with what you said. My post was more of an optimistic look at how it outta be. I’ve dealt with the same exact thing you speak of. It’s like you can’t even ask a simple question without certain youtubers getting immediately defensive + waiting for their flock to jump in. It’s weak!
Couple that with the disinformation aspect (ONE guy had something break, and he posts that the ENTIRE product line is garbage and DO NOT buy it).
Youtube is becoming very hard to wade through nowadays. JMO
-
Re: Pressure washer kinkless hose
https://uploads.tapatalk-cdn.com/201...44e7b21fe3.jpg
Got this at HD (exclusive to them). They have a short video on site... looks to be pretty flexible. 1/4 inch and feels nice. 35 ft.... works for me.
Sent from my iPhone using Tapatalk
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
Coatingsarecrack
So after using a couple times still very stiff. Doesn’t want to uncoil. The video shows guy turning on on pressure washer and walking away and it uncoiling....no chance. Was thinking uberflex but a lot of bad reviews on marring and blow outs. Ordered a flexzilla 50ft 1/4th inch. Was only 59.99 very reasonable and has been great two weeks I’ve used it very flexible and lays flat. Didn’t really need 50 ft but needed more than 25. Thanks Eldarado for the recommendation.
https://uploads.tapatalk-cdn.com/201...2db2db4ac0.jpg
Sent from my iPhone using Tapatalk
-
Re: Pressure washer kinkless hose
What brand pressure washer you running? Might need one for mine 25 isn’t enough
Sent from my iPhone using Tapatalk
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
minerigger
What brand pressure washer you running? Might need one for mine 25 isn’t enough
Sent from my iPhone using Tapatalk
Ryobi 2300 psi 1.2 gsm electric
Sent from my iPhone using Tapatalk
-
Re: Pressure washer kinkless hose
Hmm. I’ll have to look and see if this works in the sun joe 3001xp or whatever the hell I have
Sent from my iPhone using Tapatalk
-
Re: Pressure washer kinkless hose
Quote:
Originally Posted by
minerigger
Hmm. I’ll have to look and see if this works in the sun joe 3001xp or whatever the hell I have
Sent from my iPhone using Tapatalk
Yeah I just added 3/8ths quick connects each end and seems to work well
Sent from my iPhone using Tapatalk