Dislikes: 0
-
Regular Member
Foam pad life expectancy
What is the average life expectancy of foam buffing pads. I have many LC and Hex Logic pads. I wash w APC, spin dry (w buffer) and let dry upside down always after each use. They don't seem to be losing effectiveness but I've had some of these pads for years... like 6-7.
Thanks.
-
Super Member
Re: Foam pad life expectancy
It really depends on how they are used.
If you overuse them once they start to get saturated you could destroy a pad in a single use. OTOH, if you use some common sense and change your pad before they get to the saturation point they will last a long, long time.
Properly used, cleaned, and stored, they will last almost indefinitely. Not forever, but a long time.
If the foam isn't deteriorated, the velcro is still intact, and the pad feels generally ok - Polish on!
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
-
Super Member
Re: Foam pad life expectancy
Store the pads in room temperature. I stored mine in a hot garage and they got totally trashed. That was an expensive lesson. I haven't fully replaced them all yet
Treat it like it's the only one in the world.
-
Super Member
Re: Foam pad life expectancy
I have several that are 5 years old, one of the benefits of using multiple pads per session is that you don’t overheat/ abuse them which is the #1 enemy to pad life
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
-
Super Member
Re: Foam pad life expectancy
7 years is a lot to ask out of a pad. If it were me, before you start your next detail order some new pads in the color you are planning to use.
Check to see if the velcro is firmly attached to the foam pad. This is where I see most failures.
At 5+ years, I start to see the foam deteriorate where the velcro is attached.
-
Super Member
Re: Foam pad life expectancy
Originally Posted by 2black1s
It really depends on how they are used.
If you overuse them once they start to get saturated you could destroy a pad in a single use. OTOH, if you use some common sense and change your pad before they get to the saturation point they will last a long, long time.
Properly used, cleaned, and stored, they will last almost indefinitely. Not forever, but a long time.
If the foam isn't deteriorated, the velcro is still intact, and the pad feels generally ok - Polish on!
^^^This^^^
I have used 20 pads on my full-sized truck. Is that overkill? Yeah, it probably is. Could I have used 10 and produced the same result? Sure.
But..... Each of those 20 pads were barely dirty, hardly got warm, and were a breeze to clean. Therefore, they will last a very, very long time.
Am I saying everyone should use 20 pads? Of course not. But using a few more pads than you think you may need is way better than overworking too few pads.
It is no coincidence that man's best friend cannot talk.
-
Post Thanks / Like - 1 Thanks, 2 Likes, 0 Dislikes
-
Super Member
Re: Foam pad life expectancy
Originally Posted by PaulMys
^^^This^^^
I have used 20 pads on my full-sized truck. Is that overkill? Yeah, it probably is. Could I have used 10 and produced the same result? Sure.
But..... Each of those 20 pads were barely dirty, hardly got warm, and were a breeze to clean. Therefore, they will last a very, very long time.
Am I saying everyone should use 20 pads? Of course not. But using a few more pads than you think you may need is way better than overworking too few pads.
Your anal!
-
Post Thanks / Like - 1 Thanks, 2 Likes, 0 Dislikes
-
Super Member
Re: Foam pad life expectancy
Very early on i stored my foam pads in the garage...in FL! Not good. Some turned to dust from the excessive heat. Now all my pads are kept in the air conditioned space inside.
-
Super Member
Re: Foam pad life expectancy
That is exactly what happened to me. I now store pads and polishes in the houss
Treat it like it's the only one in the world.
-
Re: Foam pad life expectancy
I've only been at this 2+ years but the way i use them they will last a very longtime. My rule of thumb: Use One 5 inch pad on 2 car doors max - i have a 3 inch for edge work or a medium sized bonnet.
Washing: I simply have a short piece of cutoff garden hose attached to my tap so when i pinch/fold the end of the hose it creates a moderate level of pressure. I usually spray APC directly in the pad, use the hose to rinse the APC with hot water for a few seconds then i will switch to warm water and hand wash. Air dry.
Very simple process, it works so i never tried doing anything else.
Similar Threads
-
By Northwoods in forum Auto Detailing 101
Replies: 1
Last Post: 09-18-2019, 09:03 AM
-
By goldenlight in forum Auto Detailing 101
Replies: 27
Last Post: 01-04-2014, 10:00 AM
-
By EWtheDETAILER in forum Ask your detailing questions!
Replies: 11
Last Post: 08-29-2013, 07:14 AM
-
By alko in forum Auto Detailing 101
Replies: 12
Last Post: 08-15-2011, 11:47 AM
-
By Plan b Detail in forum Auto Detailing 101
Replies: 7
Last Post: 08-03-2011, 11:13 PM
Members who have read this thread: 1
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
S |
M |
T |
W |
T |
F |
S |
31 |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
| 1 | 2 | 3 | 4 |
|
Bookmarks