Dislikes: 0
-
CQUK difficultlies
I’ve been installing CQUK on my civic for the first time and I can’t say it was a smooth sailing. Ambient temp in the garage was around 65 with humidity in low 40s. The problem is that coating would become sticky the very second it got on the paint. I wouldn’t even be able to level it out with applicator pad before it becomes sticky and grabby. And it wouldn’t even flash yet (visually it would start flashing with 3-3.5min). I was able to remove with mf towel but it wasn’t anywhere close to what I saw in the videos. I ended up leaving it on the paint for 2-3 minutes before removing it and used short pile mf towel using short strokes with very little pressure (otherwise it would just grab and hold me back).
What was I doing wrong? Waited too long and too short? Bad weather conditions? Anything else???
Sent from my iPhone using Autogeekonline mobile app
-
Super Member
Re: CQUK difficultlies
Check the date on the bottle, could be old and/or partially cured.
Typically, I will go through 3 suede applicators to do one vehicle. After 1/3 of the car or so application can get grabby as you have described, which is when I grab a new one.
Final thought is that you may not be using enough product.
-
Re: CQUK difficultlies
Originally Posted by Audios S6
Check the date on the bottle, could be old and/or partially cured.
Typically, I will go through 3 suede applicators to do one vehicle. After 1/3 of the car or so application can get grabby as you have described, which is when I grab a new one.
Final thought is that you may not be using enough product.
Thanks for the feedback. 3 applicators was exactly how many I’ve used. Also the product is pretty fresh, around 3 months old. Opposite to your suggestion I think I used too much of the product - whole car and twice covering the hood and I got left a little over 1/3 of the bottle. Could that be a problem?
Sent from my iPhone using Autogeekonline mobile app
-
Super Member
Re: CQUK difficultlies
Hi,
you did well, CQUK dont need flashing time , you can apply on and wipe off, doing even layer not too thick.
work on small areas, like 50cm2 , almost WOWO , the sticky feel is the reaction of the coat , might be the humidity you had too
so even if you wipe off right after its fine, using short loops mf or the suede mf we supply for wipe off.
-
Post Thanks / Like - 3 Thanks, 3 Likes, 0 Dislikes
-
Re: CQUK difficultlies
Originally Posted by Avi@CarPro
Hi,
you did well, CQUK dont need flashing time , you can apply on and wipe off, doing even layer not too thick.
work on small areas, like 50cm2 , almost WOWO , the sticky feel is the reaction of the coat , might be the humidity you had too
so even if you wipe off right after its fine, using short loops mf or the suede mf we supply for wipe off.
Thanks for the feedback. Yesterday I was doing another car and used Essense as a primer and it made a HUGE difference. Coating went on so much smoother and wiping off was much easier. On the other hand, I got a 50ml of regular CQ I’ll be using. How different is it from CQUK? I believe I have to wait for it flash before wiping it off? Any tips you could share?
Sent from my iPhone using Autogeekonline mobile app
-
Super Member
Re: CQUK difficultlies
Just curious, with the seeming problematic application, I assume you used a paint prep (Carpro Eraser) prior to the coating, correct?
The first thought was as your first reply in this thread, that the coating was past its expiration date.
I had noted such occurs, that CQuartz can get a little "sticky" and harder to apply when it gets old.
I used a quite old bottle to coat my 6x12 Cargo Trailer last fall. It was just about 2 years past expiration, but never opened. Coming behind to wipe in a small area as a initial test did prove a streaky smeary mess, so I left well enough alone, just applied with the Foam Block and MF Suede Sheets, and didn't touch it after.
Amazingly, I still got beautiful end results. Although I was not looking to achieve perfection as it is just a trailer, I do know I laid down some very good protection on a 15 year old paint finish.
-
Re: CQUK difficultlies
CQUK is typically all I use. I just had to do a spot buff on a car w/ CQUK this morning... Temps were low 60's and a skim of moisture on the vehicle. I did a rinsless on the area first, corrected the scratch, then used erasure and just as Avi stated, worked the small spot buff area... as soon as it applied, I usually just start removing. No issues. CQUK doesn't like to dwell on the paint for a long time.
-
Post Thanks / Like - 2 Thanks, 0 Likes, 0 Dislikes
-
Re: CQUK difficultlies
Originally Posted by MarkD51
Just curious, with the seeming problematic application, I assume you used a paint prep (Carpro Eraser) prior to the coating, correct?
The first thought was as your first reply in this thread, that the coating was past its expiration date.
I had noted such occurs, that CQuartz can get a little "sticky" and harder to apply when it gets old.
I used a quite old bottle to coat my 6x12 Cargo Trailer last fall. It was just about 2 years past expiration, but never opened. Coming behind to wipe in a small area as a initial test did prove a streaky smeary mess, so I left well enough alone, just applied with the Foam Block and MF Suede Sheets, and didn't touch it after.
Amazingly, I still got beautiful end results. Although I was not looking to achieve perfection as it is just a trailer, I do know I laid down some very good protection on a 15 year old paint finish.
Correct, it was bare paint wiped with the eraser after polishing. I’ve used essense as a primer on a different vehicle it was much much better as far as ease of application and removal
Sent from my iPhone using Autogeekonline mobile app
-
Super Member
Re: CQUK difficultlies
I've used both and Cquartz TIO just isn't my cup of tea. It does provide a nice gloss and what not but it just doesn't have the same nice look at Cquartz UK nor the durability of UK.
2016 Mazda 3 Sports GT
2015 Lexus IS250 F Sport
-
Post Thanks / Like - 1 Thanks, 2 Likes, 0 Dislikes
-
Re: CQUK difficultlies
Originally Posted by WillSports3
I've used both and Cquartz TIO just isn't my cup of tea. It does provide a nice gloss and what not but it just doesn't have the same nice look at Cquartz UK nor the durability of UK.
So, when you say TIO2, do you mean regular CQuartz? I’m getting confused a bit as I don’t see it anywhere on the packaging. I got 50ml of this stuff I was planning to get use on my pilot (although pretty much half of the car is already corrected and coated with CQUK). Do you think they will look different on the same car? How’s my layers of regular CQ would you suggest to apply?
Sent from my iPhone using Autogeekonline mobile app
Similar Threads
-
By Mariana in forum Auto Detailing 101
Replies: 12
Last Post: 12-09-2018, 02:08 PM
-
By GreatAvalon in forum Auto Detailing 101
Replies: 37
Last Post: 06-14-2016, 05:50 PM
-
By Every_detail in forum Auto Detailing 101
Replies: 18
Last Post: 02-25-2016, 04:49 PM
-
By Every_detail in forum Auto Detailing 101
Replies: 3
Last Post: 02-15-2016, 08:01 PM
-
By top189h in forum Pinnacle Wax
Replies: 4
Last Post: 11-10-2014, 10:27 PM
Members who have read this thread: 0
There are no members to list at the moment.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
S |
M |
T |
W |
T |
F |
S |
31 |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
| 1 | 2 | 3 | 4 |
|
Bookmarks