Thanks: 0
Likes: 0
Dislikes: 0
-
07-17-2017, 01:27 AM
#201
Re: Flex 3401 vs. Rupes Mille/Makita P5000C, for those that are wondering.
I can wait, but I don't want to.
I am anticipating that the Mille will work well on gelcoat as a rotary alternative with the right pads; am I correct or am I still going to need/want a rotary for gelcoat correction?
-
07-17-2017, 01:37 AM
#202
Super Member
Re: Flex 3401 vs. Rupes Mille/Makita P5000C, for those that are wondering.
Originally Posted by jjackkrash
am I correct or am I still going to need/want a rotary for gelcoat correction?
here's a couple of threads you might want to check out with the flex...
Marine 31 Wool Pads in ACTION! Heavy Cut Cleaner Wax vs. Boston Whaler
https://www.autogeekonline.net/forum...n-removal.html
-
07-17-2017, 06:55 AM
#203
Super Member
Re: Flex 3401 vs. Rupes Mille/Makita P5000C, for those that are wondering.
Originally Posted by jjackkrash
I can wait, but I don't want to.
I am anticipating that the Mille will work well on gelcoat as a rotary alternative with the right pads; am I correct or am I still going to need/want a rotary for gelcoat correction?
Oxidation can be quite deep - as you remove the damaged paint it needs somewhere to go. This is why wool pads, with their increased surface area, can be so effective. RUPES will be launching specifically designed wool pads, tuned and balanced for the Mille, which should be the answer on those thickly oxidized gel coats.
As Visitor nicely pointed out, if current gear-driven polishers work, then the Mille should work even better! Gel-coat work, even with a gear-driven polisher can take time. With the Mille, and its carefully designed ergonomics and minimal steering, I have a feeling a lot of marine detailers and boat owners are going to be very grateful.
With all of the above said, nothing can produce the cutting power potential of a rotary polisher. It is able to develop a high amount of speed on the pad's edge which gives it the highest potential for cut. On some gel coats with really deep, really hard oxidation, you may still get the fastest initial cut by starting with a rotary polisher and a wool pad.
-
07-17-2017, 08:05 AM
#204
Re: Flex 3401 vs. Rupes Mille/Makita P5000C, for those that are wondering.
Originally Posted by jjackkrash
am I correct or am I still going to need/want a rotary for gelcoat correction?
Depends on how deep the oxidation is and your expectations for a "nice" finish.
I cover deep oxidation in my boat classes, the next class is February 10th and 11th, 2018 - The fastest and easiest way to remove deep oxidation is to machine sand and then compound with a wool pad on a rotary buffer.
I also cover this in my boat detailing how-to book. This is the most in-depth how-to book I've ever written due to how many tools there are on the market and also the wide spectrum of "conditions" boats can be in. Suffice to say, it's a lot more complex to "type" about than car detailing.
There a 6 pages to the index alone. Here's the third page,
I divided boat conditions into 4 categories,
Category #1 New or Like New
Category #2 Good Condition with Light Oxidation
Category #3 Mild Neglect
Category #4 Severely Oxidized and Neglected
Category #1 you're good to go with a free spinning orbital polisher. Any free spinning orbital polisher s long as you can maintain pad rotation and pad oscillation.
Category #2 you're good to go with any gear-driven orbital polisher or rotary buffer. Oxidation can be removed to a satisfactory level with a free spinning tool but it's going to take longer as compared to any gear-driven tool. Your time, you're money.
Category #3 - At this level of oxidation, the fastest way to and here's the key word, thoroughly remove deep oxidation is with a rotary buffer, wool pad and top notch compound. You can use a gear-driven orbital but it's going to take longer to get the same results you can achieve using a rotary with a wool pad.
Category #4 - At this level of deep oxidation the fastest and most effective way to thoroughly remove oxidation is to machine sand to a fresh base of gel-coat and then remove your sanding marks using a rotary buffer. You can skip sanding and only use a rotary buffer but >you< are going to PUSH hard for HOURS against a surface that declines or angels away from you, very tough to do for hours. The results will look splotchy unless you REALLY focus on working small areas and closely monitor your pad overlap not only for the section you're buffing but when moving to a new section.
At our boat detailing classes I bring in the WORST condition dark colored gel-coat boats and then show All of the above.
Heck, you can oxidation by hand if you want and I show how in my boat detailing book but what I also say in the chapter on removing oxidation on boats in category #3 on page 54 is this,
Originally Posted by Mike Phillips
My guess is that anyone attempting to correct the finish on a boat in Category #3 by hand will get about an hour into the correction process before deciding to switch to a machine.
I didn't address how to remove deep oxidation by hand for boats in category #4 because I don't know if there's a human alive that could do an entire boat. BUT if someone wanted to the 4-step process I outline for boats in category # would also work for boats in category #4.
-
07-17-2017, 08:13 AM
#205
-
07-17-2017, 09:45 AM
#206
Re: Flex 3401 vs. Rupes Mille/Makita P5000C, for those that are wondering.
Mike, your Marine detailing book and the Rupes Polisher books came this weekend! I got through a big chunk of both last night instead of watching Game of Thrones.
I am not opposed to using a rotary for bad cases, but looking to get away from a rotary unless its really needed.
-
07-17-2017, 10:39 AM
#207
Super Member
Re: Flex 3401 vs. Rupes Mille/Makita P5000C, for those that are wondering.
the Flex 3401 has been tried and true for many years and has proven itself (very reliable German tool) to work in a variety of situations (it's been known to even detail Aircraft!). there is also a Flex service center here in the states in Omaha, NE (Powerhouse Distributing) that has been around since the beginning to service the tool if needed. they (Flex) also have a new mini DA coming out soon as well (pictured below to the right). they don't call the Flex 3401 the BEAST for nothing!
https://www.flex-tools.com/en/products/polishers-2/
-
07-17-2017, 10:10 PM
#208
Re: Flex 3401 vs. Rupes Mille/Makita P5000C, for those that are wondering.
VISITOR, thanks for the tip. I just bought a set of Rupes DA's and I'm pretty impressed with their build quality. I also like the idea of sticking with their "system" so to speak. If I went another route it would probably be with Makita, as I have virtually all of their cordless tools and a slew of other Makita corded tools, and I have never ever been sorry I bought a Makita.
That said, I am also a big fan of German engineering, so maybe I will give the Flex tools a closer.
-
09-17-2017, 04:47 AM
#209
Re: Flex 3401 vs. Rupes Mille/Makita P5000C, for those that are wondering.
So whats the favorite atm? Makita or rupes?
-
09-17-2017, 05:17 AM
#210
Re: Flex 3401 vs. Rupes Mille/Makita P5000C, for those that are wondering.
Originally Posted by WRAPT C5Z06
I FB messaged Todd Helme(I trust very much) of Rupes asking him....
Sent from my iPhone using Tapatalk
"Orbit size is not that important on a gear driven" Is that an odd statement. I thought the orbit is what prevents these da's from causing swirls. If orbit size wasn't important wouldn't we be using rotaries?
Similar Threads
-
By Dan Tran in forum Auto Detailing 101
Replies: 3
Last Post: 10-25-2019, 05:52 AM
-
By Trevine in forum Auto Detailing 101
Replies: 36
Last Post: 03-15-2019, 04:04 PM
-
By TTQ B4U in forum RUPES BigFoot Oribital Polishers
Replies: 88
Last Post: 10-22-2018, 08:26 PM
-
By minirips2 in forum Ask your detailing questions!
Replies: 10
Last Post: 04-16-2018, 09:36 AM
-
By Mike@ShineStruck in forum Auto Detailing 101
Replies: 0
Last Post: 12-23-2017, 02:47 PM
Members who have read this thread: 0
There are no members to list at the moment.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
S |
M |
T |
W |
T |
F |
S |
31 |
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
| 1 | 2 | 3 | 4 |
|
Bookmarks