Damonsfcd
09-25-2015, 05:48 PM
Hey all, hope I'm posting this in the right forum. I wanted a little feedback to some questions, so I found the 101 forum right for the job.
So I had someone call me about a 2015 Ford Fusion. They said their baby had spilled some milk in the back seat. So I drove down to have a look. I was surprised. The car looked several years old inside, but the odometer was reading just over 10k miles. Well, I don't yet have an extractor so I decided to rent a good ol' rug doctor. The clients were friends so there wasn't any money involved.
My process was as follows:
Pretreat with Folex.
Extract. Oxy Clean was in the rinse container. I dumped three scoops in a 5 gallon bucket and filled it up to the top, mixed well and filled the rinse container with that.
Using the extractor, I made one pass with the trigger squeezed and then two to three passes with the vac only. Repeat until stains disappear.
Then I let the carpet/upholstery dry.
Lastly, after everything was dry the first time, I spot-treated remaining stains with Wolfgang Carpet and Upholstery Restorer.
Here are the results:
Rear driver seat before:
http://www.autogeekonline.net/gallery/data/500/medium/reardriverseatb4.JPG
And after:
http://www.autogeekonline.net/gallery/data/500/reardriverseatafter.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100063)
Rear driver floor:
http://www.autogeekonline.net/gallery/data/500/reardriverfloorb4.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100062)
http://www.autogeekonline.net/gallery/data/500/reardriverfloorafter.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100061)
Front Passenger side:
http://www.autogeekonline.net/gallery/data/500/frontpassseatb4.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100060)
http://www.autogeekonline.net/gallery/data/500/frontpassseatafter.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100059)
http://www.autogeekonline.net/gallery/data/500/frontpassfloorb4.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100058)
http://www.autogeekonline.net/gallery/data/500/frontpassfloorafter.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100057)
Front driver's side floor: (seat was ok, despite the rest of the inside)
http://www.autogeekonline.net/gallery/data/500/frontdriverfloorb4.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100056)
http://www.autogeekonline.net/gallery/data/500/frontdriverfloorafter.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100055)
Rear passenger side:
http://www.autogeekonline.net/gallery/data/500/medium/rearpassseatb4.JPG
http://www.autogeekonline.net/gallery/data/500/medium/rearpasseatafter.JPG
So my question is: Should I be discouraged at the results? How can I improve this process?
Thanks!
So I had someone call me about a 2015 Ford Fusion. They said their baby had spilled some milk in the back seat. So I drove down to have a look. I was surprised. The car looked several years old inside, but the odometer was reading just over 10k miles. Well, I don't yet have an extractor so I decided to rent a good ol' rug doctor. The clients were friends so there wasn't any money involved.
My process was as follows:
Pretreat with Folex.
Extract. Oxy Clean was in the rinse container. I dumped three scoops in a 5 gallon bucket and filled it up to the top, mixed well and filled the rinse container with that.
Using the extractor, I made one pass with the trigger squeezed and then two to three passes with the vac only. Repeat until stains disappear.
Then I let the carpet/upholstery dry.
Lastly, after everything was dry the first time, I spot-treated remaining stains with Wolfgang Carpet and Upholstery Restorer.
Here are the results:
Rear driver seat before:
http://www.autogeekonline.net/gallery/data/500/medium/reardriverseatb4.JPG
And after:
http://www.autogeekonline.net/gallery/data/500/reardriverseatafter.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100063)
Rear driver floor:
http://www.autogeekonline.net/gallery/data/500/reardriverfloorb4.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100062)
http://www.autogeekonline.net/gallery/data/500/reardriverfloorafter.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100061)
Front Passenger side:
http://www.autogeekonline.net/gallery/data/500/frontpassseatb4.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100060)
http://www.autogeekonline.net/gallery/data/500/frontpassseatafter.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100059)
http://www.autogeekonline.net/gallery/data/500/frontpassfloorb4.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100058)
http://www.autogeekonline.net/gallery/data/500/frontpassfloorafter.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100057)
Front driver's side floor: (seat was ok, despite the rest of the inside)
http://www.autogeekonline.net/gallery/data/500/frontdriverfloorb4.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100056)
http://www.autogeekonline.net/gallery/data/500/frontdriverfloorafter.JPG (http://www.autogeekonline.net/gallery/showphoto.php/photo/100055)
Rear passenger side:
http://www.autogeekonline.net/gallery/data/500/medium/rearpassseatb4.JPG
http://www.autogeekonline.net/gallery/data/500/medium/rearpasseatafter.JPG
So my question is: Should I be discouraged at the results? How can I improve this process?
Thanks!