NickNickNick
05-11-2015, 04:20 PM
This is an update to the previous posts related to my DISO issue:
http://www.autogeekonline.net/forum/ask-expert-featuring-mike-phillips/86862-new-black-car-diso-please-help.html
http://www.autogeekonline.net/forum/ask-expert-featuring-mike-phillips/87938-update-new-black-car-diso-please-help.html
First off, a big thank you to Mike for recommending the THIN meg foam pads for the PC ... what a difference in the power of the machine! It was also much easier to handle and maneuver than using the thicker pads. Thanks!
So I used the WG twins to remove 90+% of the swirls. Perfection was not what I set out to accomplish so I am incredibly happy with the results. Pictures Below.
Here's my new dilemma - as prescribed, I applied TSR followed by the Finishing Glaze. I never got around to top it with my LSP (Colinite 915) and its been 2 weeks. I did a single rinseless wash with PLG (with carnauba) in those 2 weeks, just because. I can tell some slight swirling has reappeared.
Am I screwed and have to start over or can I make a pass with the FG and top it with LSP? Any other suggestions?
I recently picked up the XMT FG With Carnauba as well (AG BOGO!) in case that it something I can also use.
I also have a fresh bottle of CG M-Seal ... does that fit in here?
Thanks in advance!
Nick
What I was up against:
http://www.autogeekonline.net/gallery/data/2850/medium/image1295.JPG
Left untouched, right single pass with TSR:
http://www.autogeekonline.net/gallery/data/2850/medium/image2102.JPG
Left untouched, right second pass with TSR:
http://www.autogeekonline.net/gallery/data/2850/medium/image3101.JPG
Second pass full panel:
http://www.autogeekonline.net/gallery/data/2850/medium/image4101.JPG
Full panel after FG:
http://www.autogeekonline.net/gallery/data/2850/medium/image5101.JPG
http://www.autogeekonline.net/gallery/data/2850/medium/image6101.JPG
Looking good ... :
http://www.autogeekonline.net/gallery/data/2850/medium/image7101.JPG
Not a great pic but you get the idea:
http://www.autogeekonline.net/gallery/data/2850/medium/image8100.JPG
http://www.autogeekonline.net/forum/ask-expert-featuring-mike-phillips/86862-new-black-car-diso-please-help.html
http://www.autogeekonline.net/forum/ask-expert-featuring-mike-phillips/87938-update-new-black-car-diso-please-help.html
First off, a big thank you to Mike for recommending the THIN meg foam pads for the PC ... what a difference in the power of the machine! It was also much easier to handle and maneuver than using the thicker pads. Thanks!
So I used the WG twins to remove 90+% of the swirls. Perfection was not what I set out to accomplish so I am incredibly happy with the results. Pictures Below.
Here's my new dilemma - as prescribed, I applied TSR followed by the Finishing Glaze. I never got around to top it with my LSP (Colinite 915) and its been 2 weeks. I did a single rinseless wash with PLG (with carnauba) in those 2 weeks, just because. I can tell some slight swirling has reappeared.
Am I screwed and have to start over or can I make a pass with the FG and top it with LSP? Any other suggestions?
I recently picked up the XMT FG With Carnauba as well (AG BOGO!) in case that it something I can also use.
I also have a fresh bottle of CG M-Seal ... does that fit in here?
Thanks in advance!
Nick
What I was up against:
http://www.autogeekonline.net/gallery/data/2850/medium/image1295.JPG
Left untouched, right single pass with TSR:
http://www.autogeekonline.net/gallery/data/2850/medium/image2102.JPG
Left untouched, right second pass with TSR:
http://www.autogeekonline.net/gallery/data/2850/medium/image3101.JPG
Second pass full panel:
http://www.autogeekonline.net/gallery/data/2850/medium/image4101.JPG
Full panel after FG:
http://www.autogeekonline.net/gallery/data/2850/medium/image5101.JPG
http://www.autogeekonline.net/gallery/data/2850/medium/image6101.JPG
Looking good ... :
http://www.autogeekonline.net/gallery/data/2850/medium/image7101.JPG
Not a great pic but you get the idea:
http://www.autogeekonline.net/gallery/data/2850/medium/image8100.JPG