PDA

View Full Version : 3.5" or 4" pads for GG Polisher?



Pages : [1] 2

CC268
05-08-2015, 06:03 PM
Hey guys,

I have already determined (in another thread) that I will be getting some 5.5" pads to be used with a 5" backing plate.

However, I have some brand new (4 white and 4 red) 3.5" LC flat pads that I got for my Pinnacle Polishin Pal. (Lake Country Beveled Edge 3.5 Inch Pad Pack (http://www.autogeek.net/bevel-edge-4-pack.html))

I realized that I don't want to do all this buy hand so I am going to purchase a Griot's DA. So...should I get a 3" or 3.5" backing plate so that I can use these pads or would I be better suited to buy 4" pads.

I would hate to waste my 3.5" pads, but if the 4" is the better way to go then I can go that route.

Kamakaz1961
05-08-2015, 06:18 PM
3" Backing plate should be fine. The 3.5" Pads should fit the 3" Backing Plates just fine. You can also use 4" Pads with it too.

custmsprty
05-08-2015, 06:25 PM
I'd go with the 3.5 backing plate and the 4"pads. I have both and you get a lot of wobble with the 3" combo on the GG6.

CC268
05-08-2015, 10:55 PM
Haha two differing opinions...anyone else have any insight?

custmsprty
05-08-2015, 11:01 PM
Try them both and you'll see, then you'll see my pov :-) I have three Rupes tools and bought the GG6 for giggles because I got it for $97.00. I tried it for applying wax with the 3" combo, wopa wopa wopa wopa. And that was it. It's too top heavy. Haven't used it since. I had a PC and it was much better with a 3" combo but I still preferred the 3.5" bc and 4" pads. My Rupes 75 with either pads is so smooooooth.

CC268
05-08-2015, 11:13 PM
This will be my first DA and I think the Griot's will be the best starter for me. I will look into getting the 3.5" backing plate and 4" pads then.

custmsprty
05-08-2015, 11:30 PM
This will be my first DA and I think the Griot's will be the best starter for me. I will look into getting the 3.5" backing plate and 4" pads then.

It's a great choice. In retrospect when I started out I wish I had gotten the GG6 over the PC. That being said, just remember when using the smaller pads it's top heavy and if it tips over it'll waste your paint so maintain control at all times. Also, when you run smaller pads run half the speed for correction you do as compared to larger pads, smaller pads heat up faster and you'll blow out the pads fast. I learned that lesson first hand. Wax sealant application speed 1. And have fun!!

CC268
05-08-2015, 11:38 PM
Thanks for the tips!

custmsprty
05-08-2015, 11:46 PM
You bet, feel free to pm if you ave any other questions once you get started.

VISITOR
05-09-2015, 12:26 AM
I would buy both the 3" and 3.5" DA backing plates. some 4" pads aren't all the same as far as hook & loop. for example, the megs 4" pads have three inches of hook & loop. at some point you may need one more than the other or may alternate between the two...

custmsprty
05-09-2015, 12:29 AM
I use the 4" LC flat pads and recently bought some Buff and Shine 4" pads, I really like the balance and configuration of the B & S 4" pads.

d33p
05-09-2015, 01:50 AM
This will be my first DA and I think the Griot's will be the best starter for me. I will look into getting the 3.5" backing plate and 4" pads then.


The GG comes with a nice handle which will give you more control when using 3" pads.

CC268
05-09-2015, 11:59 AM
Since backing plates are fairly cheap I will just get the 3" and 3.5" backing plates. I hear a lot of good things about the buff and shine pads as well.

CC268
05-09-2015, 12:03 PM
For simplicity sake I will just buy LC flat pads as it is easy and I know what to get. They are also priced very reasonably. Trying to do this all on a budget.

custmsprty
05-09-2015, 12:32 PM
Since backing plates are fairly cheap I will just get the 3" and 3.5" backing plates. I hear a lot of good things about the buff and shine pads as well.

Save your money, once you use the 3.5" backing plate you'll never use the 3".