help with this paint problem

[c.maskelony]

A friend showed me his 2004 black Honds motorcycle that a sticker was removed by previous owner on fuel tank. paint is original and sticker has left its mark. No residue or anything like that but he tried to compound it off. did not work.
Feed back please
now there are marks from his attempt and you still see the outline where the sticker was. It was a factory sticker with something about fuel he said

[STi05']

I know in some cases stickers like that can be under the clear. I wonder if that one was and he managed to peel it up leaving a spot with no clear.

[BobbyG]

It's a small picture but it looks like he needs to do a bit more work. Perhaps hitting the area with a dual action polisher and something like Meguiar's Ultimate Compound. from there use a finer abrasive and pad combination to obtain the gloss he's searching for.

[IndeedSS]

It's a small picture but it looks like he needs to do a bit more work. Perhaps hitting the area with a dual action polisher and something like Meguiar's Ultimate Compound. from there use a finer abrasive and pad combination to obtain the gloss he's searching for.

^^^ This is sound advice.

Honda puts those stickers on top of the clearcoat. The adhesive can be difficult to remove even when using Goo Gone and heating with a hair dryer, like most recommened on mc forums. As many of those as I've removed without leaving any marring, I did manage to make a small (not noticable to anyone else) haze mark on my black 03 VTX1800.

[Flash Gordon]

It's a small picture but it looks like he needs to do a bit more work. Perhaps hitting the area with a dual action polisher and something like Meguiar's Ultimate Compound. from there use a finer abrasive and pad combination to obtain the gloss he's searching for.


:iagree:

Looks like someone used the uncooth method for sticker removal :nomore:

[c.maskelony]

the reson for the sticker removal was it was starting to peel on the edge so they just took it off. the adheavsive remover worked good but the outline was there .
Hope my PC will take care of it. Hope so I really dont want to have to use trizact on it. but thats a total last resort.
thanks

[mg6045]

looks like a scouring pad was used to remove the sticker residue. If thats the case, you will need to wetsand the area, then compound, then polish.

[IndeedSS]

the reson for the sticker removal was it was starting to peel on the edge so they just took it off. the adheavsive remover worked good but the outline was there .
Hope my PC will take care of it. Hope so I really dont want to have to use trizact on it. but thats a total last resort.
thanks

It sure looks like much more than them trying to remove the outline. Must just be the angle of the shot. Good luck, I hope its just the surface of the clear.:xyxthumbs:

[dtuna42]

looks like a scouring pad was used to remove the sticker residue. If thats the case, you will need to wetsand the area, then compound, then polish.

I thought the same thing- looks like some scouring pad damage... No reason not to try some buffing it out with some compound (such as Ultimate Compound, as recommended earlier) before wet-sanding, if for no other reason than, like me, maybe you've never wet-sanded before...

[mg6045]

I thought the same thing- looks like some scouring pad damage... No reason not to try some buffing it out with some compound (such as Ultimate Compound, as recommended earlier) before wet-sanding, if for no other reason than, like me, maybe you've never wet-sanded before...

I totally agree with you here. I have only wetsanded on a my beater truck with is my DD. I wouldnt be confident doing it on another persons vehicle. But if a scouring pad was used, there is likely very deep damage that would be safer to wetsand. People dont realize how much damage those scouring pads can do. They remove paint fast and they cut extremely deep and theres nothing uniform about it.

Obviously start with the least aggressive method, but if it was me I would have the Surbuf pad and M105 ready to go on hand. As well as 2 and 3K grit sandpaper and some ONR solution.

[Mike Phillips]

A lot of times a sticker or any type of graphic that was on the paint for some length of time will leave an imprint of itself on the paint, this is called ghosting.

Sometimes you can see a difference in paint color due to fading of the paint but sometimes it's just a imprint ring or border surrounding the shape of the graphic.

The only way to remove any type of imprint mark is to abrade the surface. If there's any fading of color under the clear layer there's no way to fix it.


Usually you will do better to rub on the affects areas by hand using a clear coat safe compound first because you can exert a lot of force to a small area with just a couple of fingers and then come back and remove any marring left by rubbing by hand using a machine.


:)