PDA

View Full Version : my 04 cobra light detail


KingCobra86
11-06-2010, 11:24 AM
gave it a good once over the other day till me what u think

steps i took to get the job done.

Meguiars clay bar

Wolfgang Total Swirl Remover 3.0 via PC blue pad

Poorboy’s World White Diamond Show Glaze via PC white pad

Pinnacle Signature Series II Carnauba Paste Wax by hand x 2

Meguiars Endurance High Gloss Tire Gel



http://i544.photobucket.com/albums/hh337/kingcobra86/04%20cobra/pod082.jpg

http://i544.photobucket.com/albums/hh337/kingcobra86/04%20cobra/pod075.jpg

http://i544.photobucket.com/albums/hh337/kingcobra86/04%20cobra/pod062.jpg

http://i544.photobucket.com/albums/hh337/kingcobra86/04%20cobra/pod069.jpg

http://i544.photobucket.com/albums/hh337/kingcobra86/04%20cobra/pod2028.jpg

http://i544.photobucket.com/albums/hh337/kingcobra86/04%20cobra/shiftlight053.jpghttp://i544.photobucket.com/albums/hh337/kingcobra86/04%20cobra/pod2026.jpg
Dubbin1
11-06-2010, 11:47 AM
You're left of center :D

Looking good :xyxthumbs:
KingCobra86
11-06-2010, 12:08 PM
You're left of center :D

Looking good :xyxthumbs:
left of center ? is that a inside joke :laughing:
Dubbin1
11-06-2010, 12:22 PM
left of center ? is that a inside joke :laughing:

Left of center in the road ;)
WRAPT C5Z06
11-06-2010, 01:24 PM
WG TSR with a blue pad? I think that's way too soft of a pad for that polish.

Then to follow with a white pad with a glaze? I think you need to swap pads with the products. ;)

Anyhow, silver is the best!
Matt S.
11-06-2010, 02:13 PM
Nice job! What kind of blue pad did you use with the TSR? A soft blue finishing pad, or Cyan hydro-tech?
KingCobra86
11-06-2010, 08:14 PM
Nice job! What kind of blue pad did you use with the TSR? A soft blue finishing pad, or Cyan hydro-tech?
its a edge pad ? it seems to work for me ? what tips do u have on how to lay it down ?:xyxthumbs:
Mirror Detailing
11-06-2010, 09:03 PM
I am guessing... roughly 440 to the ground?
KingCobra86
11-06-2010, 09:56 PM
^^460hp 493 tq tunned by gearheads in arlington tx^^
Mirror Detailing
11-06-2010, 10:24 PM
^^460hp 493 tq tunned by gearheads in arlington tx^^

dam I was close. Saw the aftercooler and exhaust. So figured probably a 2.8 pulley, intake, maf and x-pipe. What else is done? Those would be pretty impressive numbers for a BPU Cobra.
c5z06camaro
11-06-2010, 11:46 PM
wow thats one nice looking terminator.
fairlady350z
11-07-2010, 05:42 AM
Looks awesome!! I really like the last picture, with the car in focus and the background out of focus. Nice touch!!
KingCobra86
11-07-2010, 09:39 AM
dam I was close. Saw the aftercooler and exhaust. So figured probably a 2.8 pulley, intake, maf and x-pipe. What else is done? Those would be pretty impressive numbers for a BPU Cobra.
2.93 upper 4lb lower pullys, off road x pipe, steeda cold air kit, full cooling mods, steeda catback, just got done last night putting in my new spec 3+ clutch

- 2004 cobra dyno @ Gearheads performance


wow thats one nice looking terminator.
thanks bud

Looks awesome!! I really like the last picture, with the car in focus and the background out of focus. Nice touch!!
yea thats my fav that why i saved it for last:dblthumb2:
Mirror Detailing
11-07-2010, 10:31 AM
Dam that sounds good.