Bought a new pressure washer - need foam lance/gun

[JMak97008]

Backyard detailer and want my boys to help me. Just bought a Ryobi 2.3gpm, 2900psi pressure washer - https://www.homedepot.com/p/Ryobi-2-900-PSI-2-3-GPM-Gas-Pressure-Washer-RY802900/303316315. I've read a ton of threads and am confused with what I need to buy, i.e., gun, lance, fittings, etc.

I think I'd rather not have the lance, but am open to opinions on that? Do some of the foam containers just screw on to the handle of the pressure washer?

Also, I'm not really interested in spending $60 for one of these and would like some recommendations on quality, durable foam guns that will help my boys lay down some thick suds on the cars.

I think I'll be ordering a gallon of hyper wash along with it. If the gun/lance can be ordered at Amazon, the better 'cuz I have Prime.

Thanks in advance.

[briarpatch]

Foam guns attach to your garden hose, foam cannons attach to your pressure washer. I have a 20.00 'knock-off' foam cannon....it's worked very well for me so far...lots of youtube videos out there for you to see comparisons

[JHL88]

Just go to ebay and get a $20-$30 foam cannon. They are basically the same as the $80 ones found on various detailing sites

[JMak97008]

Thanks, guys...I need a foam cannon then.

Do I need to also to switch out the orifice to a smaller diameter to make better foam? If so, what diameter would you recommend?

[briarpatch]

Thanks, guys...I need a foam cannon then.

Do I need to also to switch out the orifice to a smaller diameter to make better foam? If so, what diameter would you recommend?

Typically, the smaller (1.1mm) orifice is for lower psi pressure washers...more often the electric ones. At 2900 psi. I'd say to try the standard one, and use a soap that's designed for foam cannons, like Chemical Guys Honeydew. I'm pretty sure you'll be happy with the results.

[JMak97008]

So it seems like any old foam cannon will do, eh? Something like this - Amazon.com: MATCC High Pressure Washer Gun 3000 PSI Foam Wash Gun Snow Foam Lance Snow Foam Cannon Foam Blaster With M22-14mm Thread: Automotive (https://www.amazon.com/dp/B01MYV2X8H/ref=sspa_dk_detail_7?psc=1&pd_rd_i=B01MYV2X8H&pd_rd_wg=FyOxq&pd_rd_r=8WTBVYBA2D38SFRDY2CY&pd_rd_w=mlgMZ?)

[KyleBis2]

Going with any cheap one should be fine. If it doesn't give you good results, try a different orifice size for it.

[briarpatch]

So it seems like any old foam cannon will do, eh? Something like this - Amazon.com: MATCC High Pressure Washer Gun 3000 PSI Foam Wash Gun Snow Foam Lance Snow Foam Cannon Foam Blaster With M22-14mm Thread: Automotive (https://www.amazon.com/dp/B01MYV2X8H/ref=sspa_dk_detail_7?psc=1&pd_rd_i=B01MYV2X8H&pd_rd_wg=FyOxq&pd_rd_r=8WTBVYBA2D38SFRDY2CY&pd_rd_w=mlgMZ?)

that should work just fine

[evo77]

I broke down and went and bought the Ryobi last week.

Here is what I purchased in addition:

- short nose gun W/nozzles (https://www.amazon.com/gp/product/B0796649ZL/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1) (has M22 hose hookup)
- cheap foam cannon (https://www.amazon.com/gp/product/B01CE78VO8/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1)
- 1.1mm orifice (https://www.detailedimage.com/DI-Accessories-M12/11-MM-Orifice-for-Low-Pressure-Washers-P1544/) (for foam cannon to produce thicker foam)


I was debating on a longer rubber hose but dang they are expensive. Even the stiff ones too. So for the time being I'm going to try to deal with the stock short hose until I get sick of it.

[JMak97008]

I broke down and went and bought the Ryobi last week.

Here is what I purchased in addition:

- short nose gun W/nozzles (https://www.amazon.com/gp/product/B0796649ZL/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1) (has M22 hose hookup)
- cheap foam cannon (https://www.amazon.com/gp/product/B01CE78VO8/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1)
- 1.1mm orifice (https://www.detailedimage.com/DI-Accessories-M12/11-MM-Orifice-for-Low-Pressure-Washers-P1544/) (for foam cannon to produce thicker foam)


I was debating on a longer rubber hose but dang they are expensive. Even the stiff ones too. So for the time being I'm going to try to deal with the stock short hose until I get sick of it.

Was wondering if I really needed the orifice. I'll consider getting the short gun after trying with the wand first. Thanks!

[spazzz]

I bought one of the 20ish dollar cannons from Amazon and it works fine.
A little less than 2 ounces of Optimum car wash gets me the foam I need with a 1600psi Ryobi.

I bought the MTM sg-28 spray gun and will not switch back to a wand unless I am cleaning the siding on the house.
I think the cannon is more manageable using the gun instead of dangling way out there with the wand.

Here is a helpful link.
Got rid of my Overpriced Karcher PW and bought a Cheap Ryobi & Upgraded it... way better setup!! (https://www.autogeekonline.net/forum/auto-detailing-101-a/110388-got-rid-my-overpriced-karcher-pw-bought-cheap-ryobi-upgraded-way-better-setup.html)

[advisor267]

Recently I have brought a GreenWorks Pressure washer. A long days ago, I have researched for Buying a GreenWorks pressure washer. It last I have found a great review about this from Google. GreenWorks 1600 PSI Reviews in 2018-Best Pressure Washer (http://bestwasheradvisor.com/greenworks-1600-psi-review)

You can read this review for buying the pressure washer. I am satisfied to use this.

Thanks

[CalSun Detail]

Try obsessed garage website. Matt has selected the industries best products and you can buy them as complete solution package.

[Coatingsarecrack]

I bought a suds magic from the rain Forrest retailer and works pretty good. Has brass male and female connections where bottle screws on and very sturdy. Great value. That said if it’s something you use 80% of time when washing might be worth investment. Check out the griots one when A/G has a 25% off sale


Sent from my iPad using Tapatalk