Terry cloth , microfiber and foam pads by hand difference ?? For aio, interior dressing , leather care

[wantboost]

So what's the difference and what should is use to apply the following by hand


Polish

Wax

Rim dressing

Interior dressing

Leather cleaner

Leather protectant(colinite)

[wing commander]

Waxing by hand is fine with this Wolfgang Polishin’ Pal is an ergonomically shaped urethane handle that holds specially designed foam pads using hooks & loops. (http://www.autogeek.net/polishing-pal.html) or this Griots Garage 4” Hand Waxing and Correcting Pad Kit (http://www.autogeek.net/griots-garage-4-inch-hand-kit.html) and cleaner waxes are fine however any correction to remove swirls you are going to wish for one of these Griots Garage 6 Inch Random Orbital Polisher FREE BONUS! (http://www.autogeek.net/new-griots-polisher.html). I can't even imagine trying to go beyond waxes and sealants without some type of quality machine if your budget will allow. I started by hand and found the results to be like spitting into the wind.

[fightnews]

I just used a 3" lake county black finishing pad to apply trim restorer by hand. it came out great, much better then using a foam applicator pad. it might be ruined though that plastic trim restorer is hard to get out.

[fightnews]

Waxing by hand is fine with this Wolfgang Polishin’ Pal is an ergonomically shaped urethane handle that holds specially designed foam pads using hooks & loops. (http://www.autogeek.net/polishing-pal.html) or this Griots Garage 4” Hand Waxing and Correcting Pad Kit (http://www.autogeek.net/griots-garage-4-inch-hand-kit.html) and cleaner waxes are fine however any correction to remove swirls you are going to wish for one of these Griots Garage 6 Inch Random Orbital Polisher FREE BONUS! (http://www.autogeek.net/new-griots-polisher.html). I can't even imagine trying to go beyond waxes and sealants without some type of quality machine if your budget will allow. I started by hand and found the results to be like spitting into the wind.

i find it easier to just hold the da pads by hand. i removed a scratch that way and i usually do it to get the tight spots when waxing. i just take the pad off the machine and start using it. it works good you dont need all that stuff. but then again ive never tried to do a whole car by hand that would be way to much. i agree just buy a polisher.

[wantboost]

I have a gg6 and a hand jobber . New cars I do by hand amd I have all these extra pads that's why I'm asking what they are best to be used for
Also for the following what type of pad is best to use , micro , Terry or foam....
Polish

Wax

Rim dressing

Interior dressing

Leather cleaner

Leather protectant

https://s28.postimg.org/bx8onfbpl/20170430_104342_HDR.jpg (https://postimg.org/image/bx8onfbpl/)

[ducksfan]

If you're going to put wax on by hand, I would definitely get the polish pal - it will save your hand muscles.

By rim dressing do you mean the wheels or tires? Tires: I would use a foam tire applicator (there's a few of them). Wheels: Just clean them and spray with CarPro HydroFoam or Gyeon WetCoat. I don't think anything beats this system for wheels.

Interior: They all work. It's just personal preference combined with what the situation calls for. I tend to use micros for cleaning plastics and sensitive areas, foam for applying protectants, terrys for leather and carpets. But, that doesn't mean that I won't mix and match. I do. AIO's: I'll use any of the three depending on situation or what I have with me/clean.

[Powerwheels]

I haven't been doing this long, but it seems the GG pads whether for machine or by hand just absorb way to much product when applying liquid wax or sealants. The cheap pads that come in the box spread product much further, what am I missing?

Sent from my XT1254 using Tapatalk

[AZpolisher15]

Note: It's really easy to micro-mar soft paint by hand with microfiber applicators. They're often made of cheap microfiber. It is crucial to make sure you've got even pressure across the face of the pad (i.e. watch the fingertips!).

Along that same line... I find claying absolutely necessary before hand applying anything. If you don't clay-- Little contamination bits can become dislodged and embedded in applicator pads. Combined with concentrated pressure of the fingers (or worse, finger tips), these bits can easily cause marring.

For these reasons, I stick with foam (unless I'm intentionally working on RIDS). Even then, I'd try foam first.

[wantboost]

Note: It's really easy to micro-mar soft paint by hand with microfiber applicators. They're often made of cheap microfiber. It is crucial to make sure you've got even pressure across the face of the pad (i.e. watch the fingertips!).

Along that same line... I find claying absolutely necessary before hand applying anything. If you don't clay-- Little contamination bits can become dislodged and embedded in applicator pads. Combined with concentrated pressure of the fingers (or worse, finger tips), these bits can easily cause marring.

For these reasons, I stick with foam (unless I'm intentionally working on RIDS). Even then, I'd try foam first.
For a AIO on nice pretty new car a couple years old ,is a ironx type product enough or should I clay also??
Removal of polish and wax is done with microfiber towel??

[AZpolisher15]

For a AIO on nice pretty new car a couple years old ,is a ironx type product enough or should I clay also??
Removal of polish and wax is done with microfiber towel??
Is IronX enough? I'd say no. in my opinion claying is more important than ironX.

[wantboost]

Removal of polish and wax is done with microfiber towel??

[oneheadlite]

That would be my recommendation. By design, my understanding is Microfiber is designed to lift and hold. I think I'll be much softer than your average cotton terry cloth to help prevent inducing any marring during product removal.

I want to say I've read on here people talking about using terry cloth towels for applying trim dressing as sometimes you can get streaking using microfiber.