(3rd) Pure White Golf 7Gti - Detailed by Lawrence

[lawrenceSA]

This detail was actually carried out in early December last year. The objective for this car was not outright perfection but instead just a decent improvement in all areas.


As always the engine bay was tackled first


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-2-2_zpsdvsezbgr.jpg


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-4-2_zpsodujbw4k.jpg


After carefully covering any exposed electrical bits, Carchem APC @1:5 was liberally sprayed over the entire bay via a Gloria Foam Master foam sprayer, left to dwell and then agitated using various Wheel Woolies, Speedmaster and Autofinesse brushes before being pressure rinsed. Carchem Vinyl and Rubber dressing was then used to dress the plastics and the painted surfaces were treated to Dodo Juice Lime Prime on a MF applicator.


And I then forgot to take any pictures of the completed bay - I really need to stop making this mistake :fear: Sorry.


The wheels were not very dirty at all and I never snapped and before/during pics, but they were still treated to a full clean and decon using my 'normal' approach of:
Pressure rinse fender wells, tyres, wheels and brake calipers
Spray Carchem APC @1:5 and let dwell
Agitate with various brushes
Pressure rinse
Spray Carchem Revolt, allow to dwell, agitate and pressure rinse
Spray Carpro Tar-x, let dwell, wipe with MF
Re-apply iron remover (to get any iron deposits that may have been hiding under the tar spots)
Pressure rinse


As you can see the wheels have taken a bit of a beating and had quite a lot of deep scratches and swirls


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-155_zpst1ljbtb3.jpg


I used Meguiars D300 and a Mothers Power Cone on a variable speed drill to give them a very quick polish to try and improve the look a bit - a full proper correction on the wheels was not within the scope of the detail, but as you can see, 2 quick passes with D300 did go some way in getting them looking better - definitely far from 'right' - but good enough IMO for the free 'add-on'.


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-156_zps7cygqlcn.jpg


The wheels were then sealed using Menzerna Powerlock and the tyres dressed with 2 coats of Carchem Tire Gel, 12 hours apart


With all the dirty work out of the way, it was time to get the car cleaned up but first this dealer applied sticker was removed using plastic razor blades and Carpro Tar-x to remove the glue residue.


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-50_zpsw7t8bhuw.jpg


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-58_zpsyoq6y9hm.jpg


All the loose dirt was first pressure rinsed off the car. This step will go a long way in reducing the possibility of swirls during the rest of the wash and so IMO it is worth investing in a pressure washer. The 2nd advantage of the pressure washer is that it can be paired to a foam cannon which will allow you to 'pre-soak' the car in a foam designed to help loosen the remaining dirt.


In this case, Valet Pro ANSF was used.


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-37_zpsqkuvjdpf.jpg


This was allowed to dwell during which time the badges/emblems, honeycomb, window rubbers, door handles and panel gaps were agitated using a Autofinesse Hogs Hair brush. The foam was then pressure rinsed off and Valet Pro Citrus Prewash applied to the lower half of the vehicle via a pump sprayer. This was allowed to dwell, then pressure rinsed off. The car (including the door/boot shuts) was then washed using Lambswool wash mitts, Carchem Luxury Shampoo and 2 buckets with grit guards.


Once clean the vehicle was given a quick dry to remove most of the standing water and the car then liberally sprayed with Carchem Revolt. Not much iron contamination was present and there were minimal tar spots to deal with too, which was a nice change. The remaining contamination was then clayed off using Shield Heavy Duty clay and ONR as lube.


The sunroof was then given a decent clean before paint correction commenced.


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-92_zpseevwevip.jpg


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-94_zpseviuzuas.jpg


Paint readings were taken and readings were mostly in the 120µ range. Multiple test spots were conducted resulting in a the following combinations for correction.


Paint: Menzerna SHC 300 / Blue hybrid wool pad, followed by Menzerna SF4000 on a White Hybrid pad
B-pillars: Menzerna PF2300 on an Orange hybrid followed by Menzerna SF4000 on a Black Hybrid pad
Front/Rear bumpers: Menzerna FG400 on an Orange Hybrid pad
Taillights: Menzerna PF2300 on an Orange hybrid followed by Menzerna SF4000 on a Black Hybrid pad


Here are some pics of the correction process


Paint before


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-100_zps4ugfboix.jpg


Working SHC 300


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-108_zpsdpdjxgss.jpg


The hazing left behind from the initial cut


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-139_zpsb1wf1hcm.jpg


The refined finish


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-147_zpsyfyahzyk.jpg


The b-pillars before correction


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-148_zpsrwrrqqpx.jpg


As you can see it is important to tape off the surrounding rubbers so as to prevent a) the polisher actually abrading away some of the rubber and b) leaving polish residue in the rubber which can be difficult (and often next to impossible) to remove.


Furthermore, if you look carefully you will see that the tape itself runs ever so slightly over the actual edge of the pillar itself - this is often not done resulting in the edges being 'over-polished' and the clear ultimately being polished away completely .... This will result in black paint transferring onto your pad - a sure sign that the clear has been compromised.


After


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-149_zpsv0uum2pg.jpg


Before


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-153_zpskjdaul6t.jpg


After


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-154_zps9fwgxs4d.jpg


The paint was then protected using Collinte 915


The exhaust tips were cleaned using Carchem APC @ 1:5 then polished using Mothers Mag and Aluminum Polish. The rest of the details were than taken care of


Exterior plastics
Equipment - Foam applicators, MF towels, Q-tips
Clean - Shield Heavy Duty Vinyl and Rubber Cleaner
Protect - Carchem Vinyl and Rubber Dressing


Glass
Clean - Autoglym Fast Glass, MF towels, Wynns C-Thru


Badges & Emblems
Equipment - Q-tips, MF towels
Clean/polish/protect - Autofinesse Tripple


Interior Plastics
Equipment- Foam applicators, MF towels, Q-tips, Various brushes
Clean - Carchem APC @ 1:20
Protect - Optimum Optiseal
Interior Carpets
Equipment- Brushes, Flex VL35C Vacuum


Leather Surfaces
Equipment- Foam applicators, Flex VL35C Vacuum, MF towels, Brushes
Clean - Carchem APC @ 1:20, various brushes, MF towels
Protect - Collinite 855


Here are a few pics of the finished car.


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-162_zpsbwlmwcle.jpg


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-160_zpsgyl3hxbp.jpg


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-163_zpseawfqux7.jpg


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-174_zpst5ddirnp.jpg


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-177_zpsyiu4ktyu.jpg


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-181_zpsufqzgjef.jpg


http://i1217.photobucket.com/albums/dd393/polo_playa/Detailing%20-%20Craig%20Golf%207Gti/untitled-183_zpsplkgg703.jpg


Total time spent= 31 hours


As always thanks for looking, and any questions or comments are welcome


:hi:

[Mike@DedicatedPerfection]

Damn! Impeccable work there Lawrence! That looks amazing! Nicely done. Beautiful pictures by the way. :xyxthumbs:

I bet the owner could not believe that transformation.

Thanks for sharing.

[Sean M at ShowShine]

Amazing work, that tape job is beyond impressive.

[lawrenceSA]

Damn! Impeccable work there Lawrence! That looks amazing! Nicely done. Beautiful pictures by the way. :xyxthumbs:

I bet the owner could not believe that transformation.
Thanks so much Mike.

Thanks for sharing.


Amazing work, that tape job is beyond impressive.
Thank you very much. I am a firm believer in taping up properly... the time and effort spent on this pales in comparison to the cost of either over thinning out an already thin edge or raised body line, or even worse, risking a strike through. Perhaps there are times with this overly-cautious approach lands up being 'counter-productive' but I'd rather be safe than sorry.

After all I am only a weekend warrior and so absolutely efficiency is not as important as 'quality' to me...

[atgonzales]

What is the name of the tape you used on the car


Sent from my iPad using Autogeekonline mobile app (http://r.tapatalk.com/byo?rid=87407)

[lawrenceSA]

What is the name of the tape you used on the car


Sent from my iPad using Autogeekonline mobile app (http://r.tapatalk.com/byo?rid=87407)

Its made by Carpro and comes in 5mm, 15mm and 24mm widths (3/16″, 1/2″ and 1″ [I think])

The 5mm ones is especially great from raised body lines

[atgonzales]

Thank you and great work


Sent from my iPad using Autogeekonline mobile app (http://r.tapatalk.com/byo?rid=87407)

[Sicoupe]

Stunning work my friend! You attention to detail is one of a kind Lawrence!

Kyle

[AZ Mike]

Always a joy to read your posts. Great job on that VW.

Furthermore, if you look carefully you will see that the tape itself runs ever so slightly over the actual edge of the pillar itself - this is often not done resulting in the edges being 'over-polished' and the clear ultimately being polished away completely .... This will result in black paint transferring onto your pad - a sure sign that the clear has been compromised.

Thanks for the tip. If this is part time for you, what do you do full time?

[lawrenceSA]

Thank you and great work


Sent from my iPad using Autogeekonline mobile app (http://r.tapatalk.com/byo?rid=87407)
Thank you very much


Stunning work my friend! You attention to detail is one of a kind Lawrence!

Kyle
Thanks Kyle - appreciate the kind words my friend.


Always a joy to read your posts. Great job on that VW.

Furthermore, if you look carefully you will see that the tape itself runs ever so slightly over the actual edge of the pillar itself - this is often not done resulting in the edges being 'over-polished' and the clear ultimately being polished away completely .... This will result in black paint transferring onto your pad - a sure sign that the clear has been compromised.

Thanks for the tip. If this is part time for you, what do you do full time?
Thank you Mike. I am in charge of Quality Management, as well as the Safety, Health and Environmental Management (and a bit of sustainability stuff like managing our carbon footprint etc) for a large supply chain company - been with the company 18 years now and in the logistics field my whole working career.

[vinharski]

Nice job on this GTI...turned out great

[lawrenceSA]

Nice job on this GTI...turned out great

Thank you very much!

[sproketser]

Top work on the Volks mate !